Danny's And Jeff's 6A13 turbo Conversions

dannyboyau · Post by **dannyboyau** » Tue Nov 22, 2005 5:23 pm

Thanks very much Jeff

I realised i had you phone number after i made the post

Jeff · Post by **Jeff** » Sat Dec 10, 2005 11:52 am

Hi all,
Just an update on my car.
Still having problems with heat melting my gearbox selector cables. Had Paul at Crossley have a look and he insisted that he could heat sheild them for me. So after waiting for a new set of cables, he installed them, and heat shielded them. After 1/2 an hour on the dyno, guess what?. Yes they had melted. So back to drawing board.
Anyway for some good news.
With a better tune, and getting rid of the lean spots, my baby is now making
306kw atw.
Yep, over the magic 400hp figure.
When I get time I`ll post the dyno chart.
Jeff

Jeff · Post by **Jeff** » Sat Dec 10, 2005 11:55 am

As for above post from Danny.
He has organised for PWR to make an aluminimum radiator for us. I have organised a spare radiator for them to copy and measure, so hopefully in a couple of weeks it should be available.
Cost was roughly $800.
I`ll let you know how it is going.
Jeff

Jeff · Post by **Jeff** » Sat Dec 10, 2005 12:58 pm

Here it is. Jeff

dannyboyau · Post by **dannyboyau** » Thu Dec 22, 2005 2:36 am

looking good Jeff

Good to see that motor putting out some nice power figures.

Any chance of seeing a few more detailed photos under the bonnet, I am curious to see where they mounted the waste gate and get a closer look at the inlet and exhaust manifolds they made. See if there is any ideas there i can use.

Looks like it is running good, did you get it back for christmas ? and did they say when your radiator will be ready. I am hoping mine will arrive friday but might get held up by the holidays.

Jeff · Post by **Jeff** » Thu Dec 22, 2005 12:56 pm

Hi Danny,
I`ll try to get some more photos up during xmas break.
As for my radiator, they said 10th jan. My car is up and running, and finally I can change gears easily. The only problem is now overheating. I think it is more than the radiator though.
The other day I drove it sedately for 2 kms parked for 1/2 hour then drove home only to have it boil. Interestingly the bottom rad hose was cool with the top one red hot. So I think my thermostat has sh*t itself, or my water pump.
If anyone has any ideas on how to discriminate between the two, without pulling the thing apart, I would be pleased to know.
Merry Xmas to all.
Jeff

Post by **Bennoz** » Thu Dec 22, 2005 2:06 pm

Thermostat is easy enough to test if you pull it out. Just chuck it in a pan of boiling water & see if it opens. If not, its shot

Jeff · Post by **Jeff** » Tue Dec 27, 2005 6:04 pm

Thanks Ben, but not easy to pull out.
You forget that I have a huge hairdryer blocking the way.
I was hoping to diagnose the problem without having to pull it out.
Jeff

fkndonut · Post by **fkndonut** » Fri Dec 30, 2005 3:13 pm

Jeff, those chicks in your avatar are feral. :/

dannyboyau · Post by **dannyboyau** » Fri Dec 30, 2005 6:35 pm

you obviously don't know any feral women

BuCkEt · Post by **BuCkEt** » Fri Dec 30, 2005 7:50 pm

dannyboyau wrote:you don't know what feral is if you think those girls are. Because if you knew any feral women you would know there not feral,

......dude, you could have sooo pwned him a lot better than that.

Something like....."Oh so you're *~delightful!~*?" would have done!

dannyboyau · Post by **dannyboyau** » Fri Dec 30, 2005 9:33 pm

is that better

dannyboyau · Post by **dannyboyau** » Sat Dec 31, 2005 1:58 am

took some photos of the alluminium radiator before I installed it. Will take some more in the new year when i have given the engine bay a clean.

dannyboyau · Post by **dannyboyau** » Sat Dec 31, 2005 1:18 pm

jeffs avatar

personally i find it sort of hypnotic

makes you want to reach out and give them a little bit of support

Post by **Supplanter** » Sat Dec 31, 2005 1:39 pm

Mmmmmmm, avatar...

Huh?

Oh, what were we talking about again?

Jeff · Post by **Jeff** » Sat Mar 25, 2006 11:28 pm

Just an update.
2 days before the Qld cruise, a D#$K head backed into me in a carpark. Not much damage but managed to put a hole into my intercooler with his towbar.
Glad the weather has cooled down, no longer overheating. Waiting for PWR to fix the design fault with the new aluminimum radiator Danny and I have been working on. Now it has cooled, and when I get a new intercooler will have to go to willowbank and try for the new 1/4 mile record.
Jeff

RichardB · Post by **RichardB** » Fri Mar 31, 2006 7:15 am

Looks like you guys are beating me on the power stakes so Im going to convert it to single turbo over the next coming weeks. Anything I need to watchout for other then melting cables.

Just in the middle of fitting the Galant gearbox, not too many issues once I found the correct FTO driveshafts to fit, will be finishing the gearbox this weekend.

dannyboyau · Post by **dannyboyau** » Tue Apr 11, 2006 3:47 am

going big single above the gearbox ?

ceranic coat turbo and manifolds

heatshields around turbo amd manifolds

vented bonnett to assist with cooling

bigger radiator with custom channelling of air flow

dannyboyau · Post by **dannyboyau** » Fri Apr 28, 2006 2:46 am

Jeff have you heard anything from PWR about the radiator.

Jeff · Post by **Jeff** » Fri May 05, 2006 8:42 pm

Just fitted the radiator last weekend.
Fitted great. They have fixed the rounded section on the bottom. Seems to be working well, although have not been to the track.
Also fitted my new PWR intercooler. I`m not sure whether it was loss of boost from a leak in my old intercooler, or the new PWR one, but it seems to have more grunt.
I`ll have to try to make it to Willowbank soon, for a 1/4 mile.
Thanks Danny.
Jeff