FTO Community Assistance

[Bennoz]

[PHIL069]

I'll send you the $8 Phil just coz I like your attitude towards the club (whilst having a lot of fun) and your helpful nature. And i think it's the least I could do. pm me

Well done Sahin
Should we wait and see if anyone else wants to share the cost, more members might want to be part of this maybe 4 members @ $2 each or 8 members @ $1 each

BTW, I intend engraving "Donated by the members of FTO Australia 2012" on a small metal plate and sticking it inside the fuel lid (I am a trained hand engraver, the kind of engraving that gets done on jewellery/watches), I will also take pics of the hand over and instalation.

I asked at my local "Mister Minit" store for a blank red alloy engraving plate today, after telling him what I was doing he donated the plate for free.
A big to Mister Minit

[Technikhaus]

haha that's awesome!

[bjk]

Maybe you should engrave the faces of anyone who donates!

how steady is your engraving hand?

[PHIL069]

Maybe you should engrave the faces of anyone who donates!
how steady is your engraving hand?

That's not going to be many faces so far

Anyway, received the fuel door from dstocks today Thanks again.
Will do the engraving on the weekend, hoping to do my 'random act of kindness' on monday

BTW, I thought this might bring me some good karma, but............
I worked out today that my inner passenger CV needs replacing and I have a nail in my rear tyre (I can fix this one with borrowed equipment from work, but I will have to get it refilled with nitrogen) and I dropped my smart phone today and I am left with half the screen black

[Bennoz]

my inner passenger CV needs replacing

So does mine! I went & had a spare shaft reco'ed today by my dodgy asian mate for 80 bucks

[Kustom]

Sounds like a day of badluck phil...

Unlucky!!

[PHIL069]

I have engraved a plate today and stuck it to the fuel flap. I am hoping to present it tomorrow afternoon after work.
I used a brass plate because I stuffed up the red plate, I haven't engraved anything for ages

[Technikhaus]

Damn, that looks great!
Did you do that by hand?

[PHIL069]

Damn, that looks great!
Did you do that by hand?

Thanks
Yes by hand, with a hand engraver spinning a mini carbide burr @ 30,000 rpm, just like the drill a dentist uses.

[Daniel2019]

Well done Phil

[Technikhaus]

Damn, that looks great!
Did you do that by hand?

Thanks
Yes by hand, with a hand engraver spinning a mini carbide burr @ 30,000 rpm, just like the drill a dentist uses.

That's damn good talent!

[PHIL069]

Thanks guys
Here is a pic of one that didn't make the cut and it also shows the tools of the trade.....

[Vectose]

Great work Phil, we need to get a plate made up for you. "PHIL069 - Master Tappet Adjuster and Engraver"

[PHIL069]

Great work Phil, we need to get a plate made up for you. "PHIL069 - Master Tappet Adjuster and Engraver"

I could do it right now
How about.......
Daniel2019
Master of the Fly Wheel
2012
or
Vectose
Master of Con-Rod Straight
2012
or
ZFL45H1
Master of the Injector
2012
or
God Bennoz
Beer Drinker Extroadinaire
2012

[Vectose]

[Daniel2019]

Daniel2019
Master of the Fly Wheel
2012

Do it!

[Supplanter]

You'll be in her pants in no time

[Kustom]

You'll be in her pants in no time

Good work Phil!

[shadowarrior]

That's some great work Phil. Am sure she will be super happy 3 cheers to Phil for some awesome community support

Sent from my GT-N7000 using Tapatalk 2