More Bennoz upgrades - flywheel & LSD

yano · Post by **yano** » Wed Jul 02, 2008 7:19 pm

Sorry mate but about the flywheel, I'm interested to know if you had to get it machined at all or if it was actually good enough to be fitted when sent?? Also how much did the bolts set u back???

Post by **Bennoz** » Thu Jul 03, 2008 2:05 pm

FtoSam wrote:WHere!!! i want one!!!

http://www.phantomgrip.com/index.html

They are the supplier to Camskill:
http://www.camskill.co.uk/products.php? ... b0s12p7030

Im just waiitng to confirm what Mitsubishi model it is in their list. More than likely one of the VR4s. Couple of the UK guys have used these successfully.

Yano28 wrote:Sorry mate but about the flywheel, I'm interested to know if you had to get it machined at all or if it was actually good enough to be fitted when sent?? Also how much did the bolts set you back???

Its supposedly ready to bolt on. Im going to have it rebalanced just in case thou. Im paranoid about putting on unbalanced flywheels, cause if it goes wrong, it'll take the engine with it. More of a piece of mind for me.

Bolts from memory were about $80

yano · Post by **yano** » Thu Jul 03, 2008 2:19 pm

Damn, yeh that's a pretty good point. Did you end up getting the high tensile bolts or just the one's RPW sell with the flywheel??

nvr2low · Post by **nvr2low** » Thu Jul 03, 2008 6:14 pm

hey man were can i gt the flywheels bolts and a standard flywheel as i aint got the money to buy a lightened one i need one for manual conversion

Post by **Bennoz** » Thu Jul 03, 2008 8:02 pm

You can have mine for a small price. Postage is gonna hurt thou...

jonowong · Post by **jonowong** » Thu Jul 03, 2008 8:20 pm

ill let you borrow mine if you can help with my belts!

nvr2low · Post by **nvr2low** » Thu Jul 03, 2008 11:41 pm

yeha that postage sucks how much bennoz and um it will fit a gpx as they are the same gearboxs right also need pressure plate bolts got a clutch

Post by **Bennoz** » Sat Jul 05, 2008 3:05 pm

It'll fit a GPX. I'll need to look up some postage prices. Pressure plates bolts you'll need to source. Try panelhouse for them too.

nvr2low · Post by **nvr2low** » Tue Jul 08, 2008 7:08 pm

hey bennoz got ay prices for postage have ya man

Post by **Bennoz** » Tue Jul 08, 2008 7:33 pm

No mate, will be a while yet. Its still in the car.

nvr2low · Post by **nvr2low** » Tue Jul 08, 2008 10:49 pm

hah fair enough would u have it out by like august man?

Post by **Bennoz** » Wed Jul 09, 2008 8:37 am

I'd like to think so. New diff was ordered yesterday from the US, so it should be here next weekish. Once I've got that, then my box / flywheel will be coming out.

nvr2low · Post by **nvr2low** » Wed Jul 09, 2008 5:48 pm

ok man good that will be fine as i dont wanna have to buy a new one and have to pay sh*t loads thanks man
'

nvr2low · Post by **nvr2low** » Wed Jul 16, 2008 6:29 pm

hey man when u get it out tell me aye i need it haha and your price

nvr2low · Post by **nvr2low** » Sun Jul 27, 2008 7:18 pm

Hey bennoz is their anymore news on that flywheel man