Why is it easier to turbo a GR than GPX???
Moderators: IMC, Club Staff
- FtoSam
- Oldtimer
- Posts: 3924
- jedwabna poszewka promocja
- Joined: Wed Jul 13, 2005 5:00 pm
- Location: Brisbane West
- Contact:
Why is it easier to turbo a GR than GPX???
Okay after having a quick read over redlines GR turbo thread, a lot of conversation regarded the GR as being easier to turbo than the GPX... Why is this so? I understand MIVEC would have some things to say about it but wouldnt turbo+MIVEC kick arse??? surely just reprogramming the mivec settings would compensate for the turbo's effect.
I know there should be a good reason for no one turbo'ing gpx's...
anyone care to explain?
I know there should be a good reason for no one turbo'ing gpx's...
anyone care to explain?
- FTO338
- Oldtimer
- Posts: 6712
- Joined: Sun Feb 09, 2003 6:00 pm
- Location: Port Melbourne: Pimping with RX400h, B200 Turbo.
Compression ratio on the GPX is higher which is not ideal for turbo, but in order to utilize the "MIVEC CAM" the ratio needs to be high.
Yes in theory, you can just adjust the setting of the MIVEC point to suit, but I yet to see someone who actually had done it properly.
So far I’ve seen turbo GPX are either left in high CAM setting, which mean not much low end, or using a stand alone ECU to deal with the problem, but end up with cold start problem and can only run on low psi. Which end up around 130-140kwatw.
You can leave it at very low boost and with the standard ecu and mivec setting, but I don't know how long the engine will going to last. The last person who tried had blown his engine within 3mths.
Yes in theory, you can just adjust the setting of the MIVEC point to suit, but I yet to see someone who actually had done it properly.
So far I’ve seen turbo GPX are either left in high CAM setting, which mean not much low end, or using a stand alone ECU to deal with the problem, but end up with cold start problem and can only run on low psi. Which end up around 130-140kwatw.
You can leave it at very low boost and with the standard ecu and mivec setting, but I don't know how long the engine will going to last. The last person who tried had blown his engine within 3mths.
Last edited by FTO338 on Wed Oct 11, 2006 11:58 am, edited 1 time in total.
DISCLAIMER: The above text is the personal opinion of the author and does not represent the indisputable truth. The author is not responsible for any deaths, injuries or mental illness caused by the above statments.
- FtoSam
- Oldtimer
- Posts: 3924
- Joined: Wed Jul 13, 2005 5:00 pm
- Location: Brisbane West
- Contact:
- FTO338
- Oldtimer
- Posts: 6712
- Joined: Sun Feb 09, 2003 6:00 pm
- Location: Port Melbourne: Pimping with RX400h, B200 Turbo.
Need a deep pocket or a good size bank account and then talk to Dav from RPW. Or get yourself a Honda, where parts are much cheaper.Samson wrote:unlucky.... what are my options for big power N/A??
DISCLAIMER: The above text is the personal opinion of the author and does not represent the indisputable truth. The author is not responsible for any deaths, injuries or mental illness caused by the above statments.
- Liquidity
- Grease Monkey
- Posts: 221
- Joined: Sun Sep 03, 2006 5:00 pm
- AJCFTO06
- Grease Monkey
- Posts: 114
- Joined: Mon Sep 18, 2006 5:00 pm
- Location: Brisbane
so your saying i should buy a cheap GRLiquidity wrote:Either one could be worked to ridiculous levels. Its all about money.
bang for buck, best option would be neither, i imagine. best option would probably be a 6a13tt conversion, or 4g63 conversion. Would probably end up costing about the same as a full on worked n/a 6a12 mivec, or turbo worked 6a12.

- Hobbsie
- Grease Monkey
- Posts: 391
- Joined: Wed Jul 05, 2006 5:00 pm
- Location: Brisbane
- Contact:
- FTO338
- Oldtimer
- Posts: 6712
- Joined: Sun Feb 09, 2003 6:00 pm
- Location: Port Melbourne: Pimping with RX400h, B200 Turbo.
- jonowong
- Oldtimer
- Posts: 3420
- Joined: Thu Jan 15, 2004 6:00 pm
- Location: Sydney
it is always easy to turbo a car without variable valve timing... if they worked together well wouldnt all the high performance cars have VVT? like the GTRs? and dont mention the EVO9 having mivec like the FTO because the EVO9 mivec is for fuel saving not for power
the evo9 mivec and the fto mivec work totally different
the evo9 mivec and the fto mivec work totally different
- khunjeng
- Oldtimer
- Posts: 4455
- Joined: Mon Oct 24, 2005 5:00 pm
- Location: Melbourne, Victoria
the GTR and GTST have VCT..called NVCS...its not the same. NVCS is not to be confused with VTECH which alters lift and duration high in the rev range to give higher peak power. Nissans system uses cam phasing to increase low to mid end engine torque.jonowong wrote:it is always easy to turbo a car without variable valve timing... if they worked together well wouldnt all the high performance cars have VVT? like the GTRs? and dont mention the EVO9 having mivec like the FTO because the EVO9 mivec is for fuel saving not for power
the evo9 mivec and the fto mivec work totally different
- FTO338
- Oldtimer
- Posts: 6712
- Joined: Sun Feb 09, 2003 6:00 pm
- Location: Port Melbourne: Pimping with RX400h, B200 Turbo.
Lots of cars these days have some sort of Variable Valve Timing and thats including turbos, but they are design for fuel economy and not as aggressive as the original Mivec or even some early VTEC YO!!!!! (not iVtec).
DISCLAIMER: The above text is the personal opinion of the author and does not represent the indisputable truth. The author is not responsible for any deaths, injuries or mental illness caused by the above statments.
-
- Veteran Mechanic
- Posts: 1020
- Joined: Sun Aug 04, 2002 5:00 pm
- Location: Sydney
The Air Intake sensor is different on the two cars, the gr one is external (before turbo) the mivec is on the throttle body (after the turbo).
Although a good tuner should be able to get around the hurdles of turboing the mivec.
Also both engines have the same compression ratio 10:1 only the 4cyl has a lower compression ratio of 9.5:1
Although a good tuner should be able to get around the hurdles of turboing the mivec.
Also both engines have the same compression ratio 10:1 only the 4cyl has a lower compression ratio of 9.5:1
- Nacho
- Oldtimer
- Posts: 2087
- Joined: Mon Jul 11, 2005 5:00 pm
- Location: Melbourne
-
- Grease Monkey
- Posts: 254
- Joined: Thu Apr 27, 2006 5:00 pm
- Location: SyDnEy...ClUb
- payaya
- Oldtimer
- Posts: 3670
- Joined: Sat Sep 06, 2003 5:00 pm
The VTEC YO!!!!! and Mivec is bascially an on/off switch. newer cars have a more linear system.FTO338 wrote:Lots of cars these days have some sort of Variable Valve Timing and thats including turbos, but they are design for fuel economy and not as aggressive as the original Mivec or even some early VTEC YO!!!!! (not iVtec).