ADZSKI'S FTO

mezje · Post by **mezje** » Wed Jul 13, 2016 2:22 am

Just go alixpress man, that one you linked looks exactly like the aliexpress one.

Buy 5 at once and sell them for profit, I bought 5 last time and made about $30AUD on each one I sold.

adzski · Post by **adzski** » Thu Jan 05, 2017 10:58 pm

So i started working on the car again after it sat for months.

Car is currently on stands and will be for a few months.
Plan is to go through and start restoring the car.

I have started pulling the exhaust off. Removed front bank extractor and still going through the process of the rear bank, removed the top 3 bolts, just need to drop the y pipe so i can get to the bottom four.

All my coilovers have seized, some c**t stole all my tools, including my lug nut tool, so will be removing them shortly to try and un-seize them. anyone got any advice on how to un-seize? read some threads on the drift forums and they said to soak in Coke or Vinegar.

Waiting on parts to come in so i can do more work
. Front lower ball joint
. Front and rear sway bar links
. New Stepper motor
. Inner and outer tie rod ends
. Fuel Filter

Going to order the rear camber arms either this week or the next

I finally got around to ordering the WORK wheel bolts for my VSXX wheels and also purchased the polishing kit for my wheel lips. Just need to get the tyres removed.

Will be going through and doing general servicing Gear box oil, Radiator fluid, Brake fluid.

Car wont be getting any attention for the next two weeks or so. Recently purchased a Manual BA XR6 Turbo that is going through RWC so will be working on that during the next week.

Will update as i work on car and buy new parts

Post by **Vectose** » Thu Jan 05, 2017 11:17 pm

Nice, get it ready before bonfire.

Post by **bjk** » Fri Jan 06, 2017 1:48 am

That's a hefty list of things!

Vectose wrote:Nice, get it ready before bonfire.

Also this^

mezje · Post by **mezje** » Fri Jan 06, 2017 1:13 pm

WD40 unseized mine

adzski · Post by **adzski** » Fri Jan 27, 2017 4:09 pm

Not much has happened since last update
Parts have started arriving
Ball joint, Tie rods and Tie rod ends, Drop links, Stepper motor and Fule filter all arrived.
Have not had a chance to change anything yet.
Still have not removed the Y-Pipe and rear manifold, was going to do it today but i didn't have my socket set on hand so will need to wait.

I changed some parts previously and never uploaded pictures so took some.

This also arrived today

Started doing my wheel rebuild

Sahin · Post by **Sahin** » Sat Jan 28, 2017 9:16 am

Thumbs up for the kaze roof spoiler

adzski · Post by **adzski** » Sat Jan 28, 2017 4:52 pm

Im keen to see what it will look like fitted

Technikhaus · Post by **Technikhaus** » Sun Jan 29, 2017 9:39 am

Ooh nice!

adzski · Post by **adzski** » Sun Feb 05, 2017 7:18 pm

parts are still slowly arriving.
Work wheel bolts arrived.
waiting on just some wiring plugs, rear camber arms, Gaskets for Exhaust,Intake manifold and Throttle body and a new front splitter i ordered.
considering replacing the oxygen sensory while i have everything out.

adzski · Post by **adzski** » Tue Feb 28, 2017 8:19 pm

UPDATE

Fitted my Extractors, what a pain in the ass that was.

Still havent fitted the Y-Pipe as going to buy a new oxy sensor and Heat wrap the Y-Pipe and extractors

Re-Fitted the Manifold and Throttle body with new gaskets. Also fitted a new Fuel filter. Havent changed it in the time i have owned it which was from 2011 onwards

Camber Arms came in fitted those.
Removed my coilovers, going to try and unseize them. Anyone got any ideas to do this? was going to soak in Vinegar or Coke?

Test Fitted Kaze Roof spoiler

Also purchased a Front splitter, not 100% on it though. What you guys think?

Started to clean up wiring to front indicators and foglight.
Will test fit Bumper with Splitter in coming weeks.
Next thing will be to unseize coilovers and fit the new Tie rods and Tie rods ends, Fit new front ball joints and replace end links

Post by **bjk** » Tue Feb 28, 2017 8:33 pm

Good progress. Not sure on splitter. Looks like it's a bit long but not quite deep enough to reach the back of the bumper? (if that's what you want)

Also why'd you fit the extractors if you want to wrap them?

adzski · Post by **adzski** » Tue Feb 28, 2017 8:47 pm

Yeah its one of those universal ones. doesnt quite fit the bar 100%. Might be able to mod it abit to fit better. But your right it is defiantly not deep enough.

Well i wasnt thinking when i fitted them, and after i decided i want to wrap them. But i cant be bothered removing them so will try wrap whilist on the car. Rear will be a pain in the ass. May need to remove.

Post by **bjk** » Tue Feb 28, 2017 8:58 pm

I think you probably will, yeah. Gonna be a nightmare trying to twist that stuff around everything

silverGPX · Post by **silverGPX** » Tue Feb 28, 2017 10:08 pm

Why bother wrapping it'll be right

Sent from my iPhone using Tapatalk

Sahin · Post by **Sahin** » Thu Mar 02, 2017 5:33 am

Whys there a photo of a cock next to a remote up further?lol

silverGPX · Post by **silverGPX** » Thu Mar 02, 2017 5:57 am

Sahin wrote:Whys there a photo of a cock next to a remote up further?lol

LOL

Sent from my iPhone using Tapatalk

Post by **bjk** » Thu Mar 02, 2017 10:37 am

Sahin wrote:Whys there a photo of a cock next to a remote up further?lol

Post by **Vectose** » Thu Mar 02, 2017 12:17 pm

Fkn lol

adzski · Post by **adzski** » Thu Mar 02, 2017 8:27 pm

WTF HAAHHA

FTO AUSTRALIA

ADZSKI'S FTO

Re: ADZSKI's FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO

Re: ADZSKI'S FTO