BJK's FTO #2: The GPX-R

silverGPX · Post by **silverGPX** » Mon Aug 15, 2016 9:18 pm

You can't nutsert it because then he will have to run a thinner non oem bolt.

Sent from my iPhone using Tapatalk

Post by **Bennoz** » Mon Aug 15, 2016 10:23 pm

This fucked nut will go on for 17 pages. I'm out.

Post by **Vectose** » Mon Aug 15, 2016 11:12 pm

silverGPX wrote:You can't nutsert it because then he will have to run a thinner non oem bolt.

Sent from my iPhone using Tapatalk

Just drill it out and use a bigger nutsert.

Daniel2019 · Post by **Daniel2019** » Mon Aug 15, 2016 11:39 pm

Bennoz wrote:This fucked nut will go on for 17 pages. I'm out.

"What size thread should I use if I wanna run a silver nut but don't want it to rust it has to fit perfectly but also look good and if I use this kind of nut what about the bolt for it and can I mig it or tig weld it? Maybe I will just stick weld it...

*500 photos of a bolt*

Post by **Vectose** » Mon Aug 15, 2016 11:46 pm

www.willitnutsert.com

Post by **bjk** » Tue Aug 16, 2016 2:15 am

Bennoz wrote:This fucked nut will go on for 17 pages.

Except it won't 'cause the fucker is getting welded and that's that.

Post by **Vectose** » Tue Aug 16, 2016 2:36 am

Just put some JB weld on the end of the bolt and hold it in place til it dries.

Post by **bjk** » Tue Aug 16, 2016 2:45 am

Vectose wrote:Just put some JB weld on the end of the bolt and hold it in place til it dries.

Will just seal it with a generous helping of semen.

Daniel2019 · Post by **Daniel2019** » Tue Aug 16, 2016 11:17 am

Sounds like a waste of perfectly good semen.

Post by **bjk** » Sun Aug 28, 2016 10:19 pm

Post by **bjk** » Wed Sep 14, 2016 2:21 pm

The car has sensed that Tim is leaving and is trying to convince him to stay by being cooperative.

Main crank pulley/harmonic balancer, new passenger CV joint, and tie rod and steering boot done last night. I think I have located the source of the clunking in the back, because the exhaust is sitting hard up against part of the chassis just before the rear control arm. Doesn't really explain why I think I hear it on the drivers side at the back, but it must be it.

Preparing to throw wads of cash at car. Fortunately the three businesses I want to use are all located within the same square kilometre and two on the same block, hopefully I can just have the car go from one to the other and pay my dues at the end. HIDs and parker wiring at the first, floorpan welding and maybe a new cat-back at the second, and respraying and fitting the facelift bar and fenders at the last. RIP bank balance.

Post by **Vectose** » Wed Sep 14, 2016 3:04 pm

Floorpan welding? Why not just chuck an EVO floorpan in.

Post by **bjk** » Wed Sep 14, 2016 3:24 pm

Vectose wrote:Floorpan welding? Why not just chuck an EVO floorpan in.

MAYBE I WILL mate

Oi, who changed the mate with an eight to 'mate'

Post by **Bennoz** » Wed Sep 14, 2016 4:10 pm

bjk wrote:
Vectose wrote:Floorpan welding? Why not just chuck an EVO floorpan in.
MAYBE I WILL mate

Oi, who changed the mate with an eight to 'mate'

It's Bens big penis. Was done many years ago to stop txt spking c*nts m9-1

Post by **Vectose** » Wed Sep 14, 2016 4:11 pm

Bennoz wrote:
bjk wrote:
Vectose wrote:Floorpan welding? Why not just chuck an EVO floorpan in.
MAYBE I WILL mate

Oi, who changed the mate with an eight to 'mate' :lol:
It's Bens big penis. Was done many years ago to stop txt spking c*nts m9-1

Needs an update. Times have changed m7+1

Post by **bjk** » Wed Sep 14, 2016 4:25 pm

The problem is you'll never be able to eliminate all the mathematical possibilities.

Sahin · Post by **Sahin** » Wed Sep 14, 2016 5:06 pm

Shut up m sqrt(arcos(0.438371146))

Daniel2019 · Post by **Daniel2019** » Wed Sep 14, 2016 8:08 pm

bjk wrote:The problem is you'll never be able to eliminate all the mathematical possibilities.

Not with that attitude.

Post by **Bennoz** » Thu Sep 15, 2016 9:00 am

You can never calculate wankers, it's like trying to calculate what size rims will fit.

Technikhaus · Post by **Technikhaus** » Thu Sep 15, 2016 9:10 am

Bennoz wrote:You can never calculate wankers, it's like trying to calculate what size rims will fit.

FTO AUSTRALIA

BJK's FTO #2: The GPX-R

Re: BJK's '95 FTO GPX #2!

Re: BJK's '95 FTO GPX #2!

Re: BJK's '95 FTO GPX #2!

Re: BJK's '95 FTO GPX #2!

Re: BJK's '95 FTO GPX #2!

Re: BJK's '95 FTO GPX #2!

Re: BJK's '95 FTO GPX #2!

Re: BJK's '95 FTO GPX #2!

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R

Re: BJK's FTO #2: The GPX-R