Bennoz 6A13 Conversion
Moderators: IMC, Club Staff
- Bennoz
- National President
- Posts: 23668
- jedwabna poszewka promocja
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: Bennoz 6A13 Conversion
So my GR Whiteline rear swaybar / Lancer droplink / aftermarket lower control arm experiment hasn't ended well..
- Vectose
- Forum Moderator
- Posts: 3948
- Joined: Sun Nov 28, 2010 8:45 pm
- Location: Newcastle
Re: Bennoz 6A13 Conversion
A bit of angle iron will fix that.
Bennoz wrote:A whoooole lot 'o jismTechnikhaus wrote:What is in said Bens big penis by the way?
- destinationtoby
- Broke it
- Posts: 3503
- Joined: Sat Nov 24, 2012 11:05 pm
- Location: mid north coast
Re: Bennoz 6A13 Conversion
Why don't you just go back to the standard arms?
Obviously the brackets are cheap pieces of sh*t that break & it's only a matter of time before the arms f**king snap. I've tried convincing jaan to let me swap the standard ones back in and throw the knock offs in the bin, but he likes them cos day is blu
Obviously the brackets are cheap pieces of sh*t that break & it's only a matter of time before the arms f**king snap. I've tried convincing jaan to let me swap the standard ones back in and throw the knock offs in the bin, but he likes them cos day is blu
Last edited by destinationtoby on Sun Aug 23, 2015 8:20 am, edited 1 time in total.
Because nothing is faster than a p plater in a commodore.....
except maybe a p plater on a unicorn
except maybe a p plater on a unicorn
FTOcrazy273 wrote: Destinationtoby probably has one of THE best FTO's on the forum I never get tired of looking at his pics! Good work mate!
- Bennoz
- National President
- Posts: 23668
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: Bennoz 6A13 Conversion
The thought did cross my mind Toby..
- FTODreams
- Grease Monkey
- Posts: 105
- Joined: Tue Mar 11, 2014 7:39 pm
- Location: Joondalup, Perth, WA
Re: Bennoz 6A13 Conversion
Just make a new bracket? My rear sway bar will probably have the same problem as we have the same set up except different sway bars (ultra racing). Quality these days are really lacking.
- destinationtoby
- Broke it
- Posts: 3503
- Joined: Sat Nov 24, 2012 11:05 pm
- Location: mid north coast
Re: Bennoz 6A13 Conversion
It's not the sway bar, it's the aftermarket control arms or trailing arms(can't remember which is which) standard arms have the bracket built in.FTODreams wrote:Just make a new bracket? My rear sway bar will probably have the same problem as we have the same set up except different sway bars (ultra racing). Quality these days are really lacking.
Also I think that is his second or third bracket. I went through a couple (stronger each time)
Because nothing is faster than a p plater in a commodore.....
except maybe a p plater on a unicorn
except maybe a p plater on a unicorn
FTOcrazy273 wrote: Destinationtoby probably has one of THE best FTO's on the forum I never get tired of looking at his pics! Good work mate!
- Bennoz
- National President
- Posts: 23668
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: Bennoz 6A13 Conversion
First one I've broken. Won't break now. 5mm angle iron.
- destinationtoby
- Broke it
- Posts: 3503
- Joined: Sat Nov 24, 2012 11:05 pm
- Location: mid north coast
Re: Bennoz 6A13 Conversion
Oh. Must of been Matt that broke me aswell.
I still don't trust the arms
I still don't trust the arms
Because nothing is faster than a p plater in a commodore.....
except maybe a p plater on a unicorn
except maybe a p plater on a unicorn
FTOcrazy273 wrote: Destinationtoby probably has one of THE best FTO's on the forum I never get tired of looking at his pics! Good work mate!
- FTODreams
- Grease Monkey
- Posts: 105
- Joined: Tue Mar 11, 2014 7:39 pm
- Location: Joondalup, Perth, WA
Re: Bennoz 6A13 Conversion
Yeah it's the trailing arm I think? Yeah I know that it's just the force that the sway bar exerts on the bracket is what wrecks it, was what I was trying to say. I don't exactly trust it either and half expect it to be made of something sh*t not billet 6061 or whatever it was. I chose them cause I couldn't be arsed with sourcing the bushes that go into the original trailing arm. Think the cost of them both equated to more than the new arms so just went for it.
Seems the president was one step ahead of me. Maybe weld in two bits of iron on each side of it so it's more like a triangle and that way doesn't bend. Although not sure if that would even Bend as most of the forces going to that bracket are just going up and marginally down.
Seems the president was one step ahead of me. Maybe weld in two bits of iron on each side of it so it's more like a triangle and that way doesn't bend. Although not sure if that would even Bend as most of the forces going to that bracket are just going up and marginally down.
- Vectose
- Forum Moderator
- Posts: 3948
- Joined: Sun Nov 28, 2010 8:45 pm
- Location: Newcastle
Re: Bennoz 6A13 Conversion
Here is a post we prepared earlier.....FTODreams wrote:Seems the president was one step ahead of me. Maybe weld in two bits of iron on each side of it so it's more like a triangle and that way doesn't bend. Although not sure if that would even Bend as most of the forces going to that bracket are just going up and marginally down.
Bennoz wrote:A whoooole lot 'o jismTechnikhaus wrote:What is in said Bens big penis by the way?
- Bennoz
- National President
- Posts: 23668
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: Bennoz 6A13 Conversion
Been trying to get this sorted for a while now & been wondering why half of these dual hangers are now obsolete... because Walbro have produced a 450LPH intank pump! Suitable for E85 as well. Sold!Bennoz wrote:Toying with the idea of re-jigging my fuel system. I don't much like the racket the external pump makes, plus the legalities of it.
A few years back, the yanks started developing dual pump hangers. Few available now for early Evos & Eclipses. Might see which one is the best fit & try it with dual Walbros. Can then essentially use the factory fuel lines & not have to run them all around the ass end of the car to secondary pump. * RTA Engineer likes this*
http://walbrofuelpumps.com/450lph-walbr ... 00267.html
- kiz
- SA Coordinator
- Posts: 2178
- Joined: Wed Nov 09, 2011 10:09 pm
- Location: Adelaide, South Australia
Re: Bennoz 6A13 Conversion
I just got a fat thinking about itBennoz wrote: because Walbro have produced a 450LPH intank pump!
There are two types of people on forums; those that give helpful advice, and the others
1998 Mitsubishi FTO GPVR AERO
1998 Mitsubishi FTO GPVR AERO
- kiz
- SA Coordinator
- Posts: 2178
- Joined: Wed Nov 09, 2011 10:09 pm
- Location: Adelaide, South Australia
Re: Bennoz 6A13 Conversion
But honestly, how loud is that going to be, might need to install bigger turbos to drown out the noise
There are two types of people on forums; those that give helpful advice, and the others
1998 Mitsubishi FTO GPVR AERO
1998 Mitsubishi FTO GPVR AERO
- Bennoz
- National President
- Posts: 23668
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: Bennoz 6A13 Conversion
Don't care. Car makes enough noise as it is
This is planning for my next forged donk!
This is planning for my next forged donk!
- destinationtoby
- Broke it
- Posts: 3503
- Joined: Sat Nov 24, 2012 11:05 pm
- Location: mid north coast
Re: Bennoz 6A13 Conversion
Got a mate that's just finished a build & we heard the fuel pumps for the first time yesterday, duel aeromotive eliminators in the boot, dynamatted to the shithouse and they're still the loudest f**king thing on earth, literally can't hear the 1600hp engine over them. He's not sure what to do about it lol but definitely can't keep them in the car that loud. Sounds like a f**king 2stroke motorbike at full throttle constantly.
Because nothing is faster than a p plater in a commodore.....
except maybe a p plater on a unicorn
except maybe a p plater on a unicorn
FTOcrazy273 wrote: Destinationtoby probably has one of THE best FTO's on the forum I never get tired of looking at his pics! Good work mate!
- bjk
- Totes
- Posts: 5749
- Joined: Tue Oct 04, 2011 1:34 pm
- Location: Adelaide
Re: Bennoz 6A13 Conversion
I await the day when fuel pump drone achieves the same status as exhaust note.
"Hey guys, new to the club! Want do my first fuel pump mod to my new car! Looking for less of a whine and more of a buzz. What would you recommend?"
"Hey guys, new to the club! Want do my first fuel pump mod to my new car! Looking for less of a whine and more of a buzz. What would you recommend?"
- Daniel2019
- Oldtimer
- Posts: 7957
- Joined: Thu Jan 12, 2012 12:25 pm
- Location: Sydney!
- Contact:
Re: Bennoz 6A13 Conversion
I love the sound of loud fuel pumps, is that weird?
I fix cars.
Bennoz wrote:I got Bali beli & sharted on my phone. But it was fun
bjk wrote:you old people are no help at all.
- destinationtoby
- Broke it
- Posts: 3503
- Joined: Sat Nov 24, 2012 11:05 pm
- Location: mid north coast
Re: Bennoz 6A13 Conversion
Dude there's no way u could love the sound of these.Daniel2019 wrote:I love the sound of loud fuel pumps, is that weird?
I had a loud external walbro in the hilux, and it was cool. These eliminators u have to talk louder to actually have a conversation in the car etc
Because nothing is faster than a p plater in a commodore.....
except maybe a p plater on a unicorn
except maybe a p plater on a unicorn
FTOcrazy273 wrote: Destinationtoby probably has one of THE best FTO's on the forum I never get tired of looking at his pics! Good work mate!
- Daniel2019
- Oldtimer
- Posts: 7957
- Joined: Thu Jan 12, 2012 12:25 pm
- Location: Sydney!
- Contact:
Re: Bennoz 6A13 Conversion
I had a stupidly loud one in the eggbeater. The motor was so loud you couldn't have a conversation at all when the car was running and never bothered installing a head unit because you wouldn't be able to hear it. Couldn't hear the pump when the car was running either.. but uber loud when ignition was on with engine off. Loved it.
Maaaaaaaaaaaaaad!
Maaaaaaaaaaaaaad!
I fix cars.
Bennoz wrote:I got Bali beli & sharted on my phone. But it was fun
bjk wrote:you old people are no help at all.
- destinationtoby
- Broke it
- Posts: 3503
- Joined: Sat Nov 24, 2012 11:05 pm
- Location: mid north coast
Re: Bennoz 6A13 Conversion
Daniel2019 wrote:I had a stupidly loud one in the eggbeater. The motor was so loud you couldn't have a conversation at all when the car was running and never bothered installing a head unit because you wouldn't be able to hear it. Couldn't hear the pump when the car was running either.. but uber loud when ignition was on with engine off. Loved it.
Maaaaaaaaaaaaaad!
Because nothing is faster than a p plater in a commodore.....
except maybe a p plater on a unicorn
except maybe a p plater on a unicorn
FTOcrazy273 wrote: Destinationtoby probably has one of THE best FTO's on the forum I never get tired of looking at his pics! Good work mate!