
The mighty Mini
Moderators: IMC, Club Staff
- aza013
- NSW Coordinator
- Posts: 9089
- jedwabna poszewka promocja
- Joined: Mon Mar 26, 2007 5:00 pm
- Location: The Shire
- Contact:
Re: The mighty Mini
That is a great power out put for a mini
.

- Kustom
- Oldtimer
- Posts: 6144
- Joined: Sun Oct 04, 2009 5:00 pm
- Location: Brisbane
- Bennoz
- National President
- Posts: 23676
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: The mighty Mini
Who needs forced induction when you've got Weber carb roar

- shadowarrior
- Tightarse
- Posts: 2703
- Joined: Thu Oct 27, 2011 4:48 pm
- Location: Gold Coast
Re: The mighty Mini
0:23 sec ... put the phone on charge Benz!! 
Sounds awesome btw

Sounds awesome btw

- Bennoz
- National President
- Posts: 23676
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: The mighty Mini
New bits 
EBC Green pads

Retro fitted Rover mini wiper motor


New VH44 booster & master cylinder


EBC Green pads


Retro fitted Rover mini wiper motor


New VH44 booster & master cylinder


- Bennoz
- National President
- Posts: 23676
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: The mighty Mini
Installed Kmac sway bar 



- dstocks
- National Vice President
- Posts: 9529
- Joined: Fri Jun 24, 2005 5:00 pm
- Location: Utopia
- Contact:
Re: The mighty Mini
Thats looking very clean Bennoz
Complete FTO (http://www.completefto.com.au/completefto.asp) 
If you are trying to contact me and not getting a quick answer, its because im disorganised. Hassle me and ill get back to you

If you are trying to contact me and not getting a quick answer, its because im disorganised. Hassle me and ill get back to you
- Astron_Boy
- Trolling Gen Y
- Posts: 8400
- Joined: Sun May 27, 2007 5:00 pm
- Location: Wine Country NSW
- Contact:
-
- 9.5"
- Posts: 6793
- Joined: Tue Oct 13, 2009 5:00 pm
Re: The mighty Mini
Astron_Boy wrote:Nice!
I'm seeing a tonne of Minis pop up around my area lately.
Lol yeah same, all real good cond too
- Bennoz
- National President
- Posts: 23676
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: The mighty Mini
They're not cheap anymore either. Used to be able to pickup a shitbox one for a 2 grand, even rusted out cars are pulling 5g & above. A fully restored Cooper S pull anywhere up to 50 grand 

- Astron_Boy
- Trolling Gen Y
- Posts: 8400
- Joined: Sun May 27, 2007 5:00 pm
- Location: Wine Country NSW
- Contact:
Re: The mighty Mini
Guy down my street with one sitting out the front of the house.Bennoz wrote:They're not cheap anymore either. Used to be able to pickup a shitbox one for a 2 grand, even rusted out cars are pulling 5g & above. A fully restored Cooper S pull anywhere up to 50 grand
Fair condition, used to have plates, and suddenly doesn't.
Obviously had enough of the brits.

I'd take it off his hands if my bug wasn't being pushed back in to my immediate possession in the near future.


- Bennoz
- National President
- Posts: 23676
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: The mighty Mini
Rebuilt the gearbox today. Not as difficult as I thought it'd be. Not logical though, had to watch a 30 minute Youtube vid to understand how it comes apart.


- Kustom
- Oldtimer
- Posts: 6144
- Joined: Sun Oct 04, 2009 5:00 pm
- Location: Brisbane
- Sahin
- HULK
- Posts: 5519
- Joined: Wed Oct 05, 2011 10:38 pm
- Location: Up to me nuts in boys guts
Re: The mighty Mini
Shoulda chucked a mini spool in it 

- Technikhaus
- Oldtimer
- Posts: 3656
- Joined: Wed Dec 28, 2011 4:45 pm
- Location: Dunedin - NZ
- Contact:
Re: The mighty Mini
Nice, how long will this one last? :p
Man '96 FTO GPX
Man '89 Legacy RS Rally car
Man '90 MR2 GT
Auto '08 Fairmont Ghia
Man '89 Legacy RS Rally car
Man '90 MR2 GT
Auto '08 Fairmont Ghia
- Bennoz
- National President
- Posts: 23676
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: The mighty Mini
So after rebuilding the gearbox, I did a quick check of the motor before I was going to put it all back together... it needed rebuilding as well
A couple of dodgy cam followers destroyed the cam. Crank is ok, just needs new big end & main bearings, also thrust washers. Don't have to pull pistons, the bores are ok.
Got all my parts bar the new cam which should arrive tomorrow. New cam bearings went in this morning.

A couple of dodgy cam followers destroyed the cam. Crank is ok, just needs new big end & main bearings, also thrust washers. Don't have to pull pistons, the bores are ok.
Got all my parts bar the new cam which should arrive tomorrow. New cam bearings went in this morning.
- Daniel2019
- Oldtimer
- Posts: 7957
- Joined: Thu Jan 12, 2012 12:25 pm
- Location: Sydney!
- Contact:
Re: The mighty Mini
Can I come to yours and spend a weekend building engines? I'm really good at replacing exhaust camshafts and if you're lucky enough to get onto me before 9am then there's a chance I'll be sober enough to go for a beer run.
I fix cars.
Bennoz wrote:I got Bali beli & sharted on my phone. But it was fun
bjk wrote:you old people are no help at all.
- Vectose
- Forum Moderator
- Posts: 3952
- Joined: Sun Nov 28, 2010 8:45 pm
- Location: Newcastle
Re: The mighty Mini
DIY day at Bennoz' :lol:
I'll build the Ikea shelving again.
I'll build the Ikea shelving again.
Bennoz wrote:A whoooole lot 'o jismTechnikhaus wrote:What is in said Bens big penis by the way?
- destinationtoby
- Broke it
- Posts: 3503
- Joined: Sat Nov 24, 2012 11:05 pm
- Location: mid north coast
Re: The mighty Mini
And I'll ahhh.... Order pizzaVectose wrote:DIY day at Bennoz'
I'll build the Ikea shelving again.
Because nothing is faster than a p plater in a commodore.....
except maybe a p plater on a unicorn
except maybe a p plater on a unicorn
FTOcrazy273 wrote: Destinationtoby probably has one of THE best FTO's on the forum I never get tired of looking at his pics! Good work mate!
- Bennoz
- National President
- Posts: 23676
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: The mighty Mini
She a farm mini now
