Engine died, very unhappy and need help :(

General Questions and comments

Moderators: IMC, Club Staff

User avatar
Foe
Grease Monkey
Posts: 104
jedwabna poszewka promocja
Joined: Tue Mar 23, 2004 6:00 pm

Engine died, very unhappy and need help :(

Post by Foe »

Well guys its been a while,
Things were going great untill yesterday when I found my self in two feet of water in a flash flood in south brisbane. Of coarse my stupid CAI sucked up the water and funnelled a generouse amount into my engine.

Anyone know what this means? Ive taken it to one place whoare saying its making a really bad knocking sound and to take it to somwhere else. My mechanic (Mclean Motors Northside) has said to bring it in for a look. Im wondering what my options are. Ive rung around and the cheapest engine Ive found is 2k. Is that good?

Also is that the ebst way to go , engine replacment? Could it be more simple? Should I give my mechanic the go ahead to check it out or just look into replacing the engine?

Thanks Guys :(
Im going off to mope :(
User avatar
GPXXX
Oldtimer
Posts: 3433
Joined: Sat Apr 12, 2003 5:00 pm
Location: < the matrix >

Post by GPXXX »

chances are you've flooded your engine with water so better dig a nice grave for it and look for a replacement motor....

R.I.P 6A12... :oops:
User avatar
frayli
Apprentice
Posts: 48
Joined: Mon Oct 18, 2004 5:00 pm
Location: melbourne

Post by frayli »

Its not always that bad i was 4wdriving in our discovery and we went through a pit that was deeper than we thought and flooded the engine.... filled every piston.... we undid the spark plugs and turned it over a few times getting all the water out had some food and let it dry for a bit. the car has been fine ever since.
G_A_V
Veteran Mechanic
Posts: 1020
Joined: Sun Aug 04, 2002 5:00 pm
Location: Sydney

Post by G_A_V »

what about rust
User avatar
Black_FTOGPX
Mechanic
Posts: 451
Joined: Sun Apr 27, 2003 5:00 pm
Location: Melbourne

Post by Black_FTOGPX »

2k sounds about right, dont forget you could sell bits and peices of your original engine to make up for some of that. :wink:
User avatar
frayli
Apprentice
Posts: 48
Joined: Mon Oct 18, 2004 5:00 pm
Location: melbourne

Post by frayli »

rust takes more than a few hours to set it all water would b evaporated as soon as enigine fires
User avatar
FTO338
Oldtimer
Posts: 6712
Joined: Sun Feb 09, 2003 6:00 pm
Location: Port Melbourne: Pimping with RX400h, B200 Turbo.

Post by FTO338 »

Hmmm do keep in mine, a 4WD are design to take lot more punishment then a sports car.
DISCLAIMER: The above text is the personal opinion of the author and does not represent the indisputable truth. The author is not responsible for any deaths, injuries or mental illness caused by the above statments.
deadpool
Newbie
Newbie
Posts: 13
Joined: Thu May 29, 2003 5:00 pm

Post by deadpool »

Did the same thing last year but killed the engine completely, :oops: freaked out for a bit, then relised I could get the whole repair covered under insurance (JustCars). They wanted to rebuild the whole thing...estimate 8-10 weeks I said don't bother and they and I agreed to a second hand engine with low k's. took the repairer 'bout 1.5 weeks and with a three month warranrty. The good news is it is way better engine more power across the band and I got a knew idle stepper motor for free cause that was affected too...and she runs like a charm :P
User avatar
dannyboyau
Veteran Mechanic
Posts: 979
Joined: Sat Sep 28, 2002 5:00 pm
Location: that speck disappearing in the distance

Post by dannyboyau »

the big problem when something like this happens is that water does not compress like air.

So if you suck in too much water you will get a hydrolic lock, this usually ends up bending conrods and damaging your bearings on your compression stroke. It also can bend valves.

Get a bicicle pump filled with air block the outlet and see how far you can push the pump handle in. now fill it with water and see the differance if it is a good quality pump it will lock up. Poor quality will let the water past the piston.

In a car engine revolving at 2000 rpm not much water will get past the piston rings on the compression stroke. so the piston will stop before it reaches top dead centre but the crankshaft will keep going and the conrod in between will usually bend or break somtimes the conrod will even go through the side of the block.
User avatar
Foe
Grease Monkey
Posts: 104
Joined: Tue Mar 23, 2004 6:00 pm

Post by Foe »

Arrrg ok so its new engine time. The 2k engine apparantly has 40k on the clock. No way to tell is there just take there word for it I guess.

Anything I shouuld look for or just take the gamble.
User avatar
Black_FTOGPX
Mechanic
Posts: 451
Joined: Sun Apr 27, 2003 5:00 pm
Location: Melbourne

Post by Black_FTOGPX »

Keep an eye out for any major oil leaks, also will you get a warranty with the engine?
User avatar
MADFTO
Mechanic
Posts: 449
Joined: Tue Apr 08, 2003 5:00 pm

Post by MADFTO »

in this instance, hydrolock probably won't be your primary concern, extreme cylinder pressures caused by expanding steam would of done the damage.

I've had water up the inlet pipe before, I think I was lucky that I didn't suck up too much, engine stalled but I didn't suck up enough water to send the compression pressures through the roof (Although my car was throwing a lot of steam out the exhaust)

Guess I was lucky I had the forethough to release the accelerator when I went through the deep puddle =)

Anyways, if you're getting knocking noises, it's either bent values, or bent conrods =/

Either are bad, new engine would probably be cheaper than a rebuild.
However, if you had the money, perfect time for modification =)
ruchi
Oldtimer
Posts: 1845
Joined: Tue Oct 14, 2003 5:00 pm
Location: Melbourne

Post by ruchi »

Do you have the standard air intake configuration or do you have an aftermarket CAI and if so what sort of airbox / enclosure do you have?
MIVEC is My Friend :D
deadpool
Newbie
Newbie
Posts: 13
Joined: Thu May 29, 2003 5:00 pm

Post by deadpool »

Did mine with the standard airbox...the wake 8O from a 4WD going the other way forced water over my bonnet :x
User avatar
Foe
Grease Monkey
Posts: 104
Joined: Tue Mar 23, 2004 6:00 pm

Post by Foe »

modified intake but standard airbox. Problem was is that I had the intake down lower then the standard intake. Im over the marginal few HP that I get with it this way and will be putting my old one back on asap.

Might even think about a pod. But probably wont thinking about selling when I get it back to gether. Bit of a shame cause the new engine Im getting apparantly has only done 60000.

Ho HUm
User avatar
dannyboyau
Veteran Mechanic
Posts: 979
Joined: Sat Sep 28, 2002 5:00 pm
Location: that speck disappearing in the distance

Post by dannyboyau »

is it a mivec engine
Dr_Jones
Veteran Mechanic
Posts: 848
Joined: Tue Sep 10, 2002 5:00 pm
Location: Brisbane
Contact:

Post by Dr_Jones »

Would an air bypass valve be used to protect ones engine from this situation
User avatar
Foe
Grease Monkey
Posts: 104
Joined: Tue Mar 23, 2004 6:00 pm

Post by Foe »

mivec
ruchi
Oldtimer
Posts: 1845
Joined: Tue Oct 14, 2003 5:00 pm
Location: Melbourne

Post by ruchi »

bugger... standard airbox sucks air in, whereas an aftermarket (non-sealed) one relies on the air being forced in and would've meant this situation wouldn't have happened (unless you were silly enough to enter the water at high speed).
MIVEC is My Friend :D
User avatar
dannyboyau
Veteran Mechanic
Posts: 979
Joined: Sat Sep 28, 2002 5:00 pm
Location: that speck disappearing in the distance

Post by dannyboyau »

would you be interested in donating the old engine to research, i would pay all shipping costs
Post Reply