Manual convert wiring

ftonoob · Post by **ftonoob** » Mon Feb 18, 2013 8:05 pm

Going from 5sp tip to 5sp manual.

How do I defeat neutral safety switch?
How to install clutch switch and get reverse light to work?

Thanks in advance.

Post by **Bennoz** » Mon Feb 18, 2013 8:30 pm

For the neutral safety you will need to join the two bigger wires (on the large black plug on auto loom) together, it's the black wire with yellow stripe and black with red stripe.

For the reverse sensor, wire in the red with blue stripe and black with yellow stripe (small wires) - they're next to each other on the auto plug.

What do you mean by clutch switch?

ftonoob · Post by **ftonoob** » Tue Feb 19, 2013 8:50 am

Would I be able to start the car with the clutch down?

Post by **Bennoz** » Tue Feb 19, 2013 10:00 am

Should be able to start it with clutch up or down - doesn't matter. There's no clutch switch.

fraz91 · Post by **fraz91** » Tue Feb 19, 2013 10:08 am

Only need a clutch switch if you're installing cruise control so that the engine doesn't rev its t!ts off when you change gear.

Post by **Vectose** » Tue Feb 19, 2013 10:34 am

You can install one if you want it as a safety feature though.

ftonoob · Post by **ftonoob** » Tue Feb 19, 2013 11:03 am

Ok. Can I get a guide to do the clutch switch?

ftonoob · Post by **ftonoob** » Fri Feb 22, 2013 9:07 am

What are my options for new flywheel bolts?

silverGPX · Post by **silverGPX** » Fri Feb 22, 2013 9:34 am

Dude. Go to a nut and bolt shop with your originals?

ZFL45H1 · Post by **ZFL45H1** » Fri Feb 22, 2013 12:35 pm

silverGPX wrote:Dude. Go to a nut and bolt shop with your originals?

This
Make sure u tell them what it for though as nuts and bolt have different grades wouldn't want the replacements to snap the heads off after putting it back together

ftonoob · Post by **ftonoob** » Sat Feb 23, 2013 8:16 am

Did that and no luck. Grade 8 bolts

ftonoob · Post by **ftonoob** » Wed Feb 27, 2013 7:55 am

Do the 6a12 and 6a13 share flywheel bolts?

ZFL45H1 · Post by **ZFL45H1** » Wed Feb 27, 2013 8:38 am

The best person to answer that would be bennoz

Post by **vipfto** » Wed Feb 27, 2013 8:39 am

YES they do

Post by **Bennoz** » Wed Feb 27, 2013 8:56 am

Yup, same same.

ftonoob · Post by **ftonoob** » Wed Feb 27, 2013 10:34 am

Good I'll have to hit mitsu for some bolts

ftonoob · Post by **ftonoob** » Sat Mar 02, 2013 6:51 am

http://www.camskill.co.uk/m3b0s12p8416/ ... E3A_2_0_V6

Would these work for my manual conversion?

ftonoob · Post by **ftonoob** » Wed Apr 03, 2013 2:08 pm

Went arp for flywheel bolts from ford 2.0l zetec engine. The reverse light wires are on the same black connector as the neutral wire or is it on the connector leading to the gear selector assembly?

ftonoob · Post by **ftonoob** » Fri Apr 05, 2013 10:46 am

Gearbox is in, wastegate actuator is shifted and car is being put back together.

ftonoob · Post by **ftonoob** » Tue Apr 09, 2013 10:37 pm

Thanks to all those who helped me out. Gearbox is in and working great. I have tons of room in the bay.

FTO AUSTRALIA

Manual convert wiring

Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring

Re: Manual convert wiring