inlet manifold

Got a problem with your FTO? ask about it here

Moderators: IMC, Club Staff

Post Reply
NextLevel
Apprentice
Posts: 94
jedwabna poszewka promocja
Joined: Sat Dec 29, 2012 8:15 am

inlet manifold

Post by NextLevel »

does anyone have a help guide on "how to removing the inlet manifold?"

and also, how long does it take to remove.


cheers
Top
User avatar
Sahin
HULK
Posts: 5519
Joined: Wed Oct 05, 2011 10:38 pm
Location: Up to me nuts in boys guts

Re: inlet manifold

Post by Sahin »

Undo all the bolts and lines? make sure you dont lose any!
and as fast as you can undo the bolts lol
Top
User avatar
PHIL069
Oldtimer
Posts: 4719
Joined: Sun Sep 20, 2009 5:00 pm
Location: Central Coast > South Australia

Re: inlet manifold

Post by PHIL069 »

Don't forget to undo the bolts around the back too, if you don't it wont come off ;)

Unbolt the throttle body and let it hang, don't need to undo cables/hoses, then bolt it back on when intake is back in place.

Unplug the sensor harness's on the drivers side of the intake and leave the sensors attatched to the intake.

Take your time, don't drop any bolts/nuts/washers into the lower intake pipes, put a rag over the lower intake pipes when the upper intake is removed, check down all the intake pipes with a torch before you put it back together just to make sure there is nothing foreign down there.

Should take you an hour on your first go, 20 min when you have done it a few times.

Good Luck :D
Last edited by PHIL069 on Fri Mar 08, 2013 12:23 am, edited 1 time in total.
mikeey01nzl wrote:Hats off to you too Phil for spending so much time on the phone trying to help someone out, your a top man and only a few would've spent so much time. well done! :salut:
Daniel2019 wrote:Come on phil, we bonded at the bonfire, lets be honest here...me and phil are besties now... :lol:
Top
User avatar
Vectose
Forum Moderator
Posts: 3952
Joined: Sun Nov 28, 2010 8:45 pm
Location: Newcastle

Re: inlet manifold

Post by Vectose »

Last time I did it I wanted to see how fast I could remove the manifold.

14 minutes and 47 seconds :cheers:

Wasn't rushing it much either. Could probably get it done in 12. :lol:
Bennoz wrote:
Technikhaus wrote:What is in said Bens big penis by the way?
A whoooole lot 'o jism 8)
Top
User avatar
Sahin
HULK
Posts: 5519
Joined: Wed Oct 05, 2011 10:38 pm
Location: Up to me nuts in boys guts

Re: inlet manifold

Post by Sahin »

Vectose wrote:Last time I did it I wanted to see how fast I could her to.....

14 minutes and 47 seconds :cheers: :lol:
Top
User avatar
PHIL069
Oldtimer
Posts: 4719
Joined: Sun Sep 20, 2009 5:00 pm
Location: Central Coast > South Australia

Re: inlet manifold

Post by PHIL069 »

Here we go, another pissing contest. :lol:

I can do it in 3 min flat with an angle grinder. :P

Sahin can just rip it off with his bare hands without undoing anything, 18 seconds.
Last edited by PHIL069 on Fri Mar 08, 2013 12:27 am, edited 1 time in total.
mikeey01nzl wrote:Hats off to you too Phil for spending so much time on the phone trying to help someone out, your a top man and only a few would've spent so much time. well done! :salut:
Daniel2019 wrote:Come on phil, we bonded at the bonfire, lets be honest here...me and phil are besties now... :lol:
Top
User avatar
Vectose
Forum Moderator
Posts: 3952
Joined: Sun Nov 28, 2010 8:45 pm
Location: Newcastle

Re: inlet manifold

Post by Vectose »

:lol: I like to have fun when I work.
Bennoz wrote:
Technikhaus wrote:What is in said Bens big penis by the way?
A whoooole lot 'o jism 8)
Top
User avatar
Sahin
HULK
Posts: 5519
Joined: Wed Oct 05, 2011 10:38 pm
Location: Up to me nuts in boys guts

Re: inlet manifold

Post by Sahin »

PHIL069 wrote:Here we go, another pissing contest. :lol:

I can do it in 3 min flat with an angle grinder. :P

Sahin can just rip it off with his bare hands without undoing anything, 18 seconds.
i dont even raise the bonnet... just straight thru the c**t
Top
User avatar
Vectose
Forum Moderator
Posts: 3952
Joined: Sun Nov 28, 2010 8:45 pm
Location: Newcastle

Re: inlet manifold

Post by Vectose »

Better airflow straight into the intake.
Bennoz wrote:
Technikhaus wrote:What is in said Bens big penis by the way?
A whoooole lot 'o jism 8)
Top
User avatar
Daniel2019
Oldtimer
Posts: 7957
Joined: Thu Jan 12, 2012 12:25 pm
Location: Sydney!
Contact:
Contact Daniel2019

Re: inlet manifold

Post by Daniel2019 »

Took me what.. an hour and a half to get it off at your tappet day Phil? Something like that? :lol:

But yeah just remember where stuff goes and dont drop anything :lol:
I fix cars.
Bennoz wrote:I got Bali beli & sharted on my phone. But it was fun :D
bjk wrote:you old people are no help at all.
Top
User avatar
PHIL069
Oldtimer
Posts: 4719
Joined: Sun Sep 20, 2009 5:00 pm
Location: Central Coast > South Australia

Re: inlet manifold

Post by PHIL069 »

Take a couple of pics as you go for reinstalling reference. :idea:
mikeey01nzl wrote:Hats off to you too Phil for spending so much time on the phone trying to help someone out, your a top man and only a few would've spent so much time. well done! :salut:
Daniel2019 wrote:Come on phil, we bonded at the bonfire, lets be honest here...me and phil are besties now... :lol:
Top
NextLevel
Apprentice
Posts: 94
Joined: Sat Dec 29, 2012 8:15 am

Re: inlet manifold

Post by NextLevel »

you guys crack me up :lol:

thanks for the tech tips fellas.
Top
Post Reply

Return to “FTO Help”