DIY: How to change your fuel filter
Moderators: IMC, Club Staff
- Vectose
- Forum Moderator
- Posts: 3948
- jedwabna poszewka promocja
- Joined: Sun Nov 28, 2010 8:45 pm
- Location: Newcastle
DIY: How to change your fuel filter
Just thought we might as well put this in the DIY section so people can stop asking.
You will need:
14mm Flare Nut Spanner for the bottom flare nut
19mm Spanner for the top bolt
12mm Spanner or socket
10mm Spanner or socket
Step 1. Remove the bottom rear seat cushion, and you will see a plate in the centre held on by four screws. Remove these four screws and then disconnect the connector from the fuel pump. Start the engine and allow it to stall on its own.
Step 2. Remove the intake pipe and battery to gain better access to the fuel filter.
Step 3. Undo the bottom flare nut using a 14mm flare nut spanner. (I did this from under the car but it is possible to do it from above.
Step 4. Undo the top eyebolt using a 19mm spanner.
Step 5. Remove the two 12mm bolts holding the bracket to the firewall.
Step 6. Remove the old filter and bracket from the car and loosen the 10mm bolt that holds the fuel filter in the bracket, Put the new filter into the bracket and tighten up the bolt.
Step 7. Put the new filter and bracket back into the car and tighten up the two 12mm bolts.
Step 8. Tighten up the bottom nut with the 14mm flare nut spanner.
Step 9. Place the two new copper washers you should have received with your new filter onto both sides of the eyebolt and then tighten it up to the filter using the 19mm spanner.
Step 10. Reconnect the fuel pump, intake pipe and battery then start the car and check for leaks.
You will need:
14mm Flare Nut Spanner for the bottom flare nut
19mm Spanner for the top bolt
12mm Spanner or socket
10mm Spanner or socket
Step 1. Remove the bottom rear seat cushion, and you will see a plate in the centre held on by four screws. Remove these four screws and then disconnect the connector from the fuel pump. Start the engine and allow it to stall on its own.
Step 2. Remove the intake pipe and battery to gain better access to the fuel filter.
Step 3. Undo the bottom flare nut using a 14mm flare nut spanner. (I did this from under the car but it is possible to do it from above.
Step 4. Undo the top eyebolt using a 19mm spanner.
Step 5. Remove the two 12mm bolts holding the bracket to the firewall.
Step 6. Remove the old filter and bracket from the car and loosen the 10mm bolt that holds the fuel filter in the bracket, Put the new filter into the bracket and tighten up the bolt.
Step 7. Put the new filter and bracket back into the car and tighten up the two 12mm bolts.
Step 8. Tighten up the bottom nut with the 14mm flare nut spanner.
Step 9. Place the two new copper washers you should have received with your new filter onto both sides of the eyebolt and then tighten it up to the filter using the 19mm spanner.
Step 10. Reconnect the fuel pump, intake pipe and battery then start the car and check for leaks.
Bennoz wrote:A whoooole lot 'o jismTechnikhaus wrote:What is in said Bens big penis by the way?
- PHIL069
- Oldtimer
- Posts: 4719
- Joined: Sun Sep 20, 2009 5:00 pm
- Location: Central Coast > South Australia
Re: DIY: How to change your fuel filter
Vectose wrote:Just thought we might as well put this in the DIY section so people can stop asking.
You're funny
mikeey01nzl wrote:Hats off to you too Phil for spending so much time on the phone trying to help someone out, your a top man and only a few would've spent so much time. well done!
Daniel2019 wrote:Come on phil, we bonded at the bonfire, lets be honest here...me and phil are besties now...
- Daniel2019
- Oldtimer
- Posts: 7957
- Joined: Thu Jan 12, 2012 12:25 pm
- Location: Sydney!
- Contact:
Re: DIY: How to change your fuel filter
I think for DIY approval it might need pics
I fix cars.
Bennoz wrote:I got Bali beli & sharted on my phone. But it was fun
bjk wrote:you old people are no help at all.
- Astron_Boy
- Trolling Gen Y
- Posts: 8400
- Joined: Sun May 27, 2007 5:00 pm
- Location: Wine Country NSW
- Contact:
Re: DIY: How to change your fuel filter
Yeah, too many Gen Y here for text only approval.Daniel2019 wrote:I think for DIY approval it might need pics
- mr_andersen
- Grease Monkey
- Posts: 126
- Joined: Sun Aug 29, 2010 11:21 pm
- Location: Perth
Re: DIY: How to change your fuel filter
Thanks for the write up Vectose.
It was a pretty straight forward job. The hardest part is just trying to get access to it. If you have huge forearms it could be a real prick of a job.
Tips:
- Depending on the size/shape of your intake pipe, you may not have to remove it to gain access.
- Getting the 14 mm flare nut and the 19 mm banjo bolt off may require a fair bit of force.
- The fuel filter and lines will still have a bit of fuel in them so use paper towels or a rag or something to catch it as you loosen the nuts.
- When you bolt the new filter back onto the firewall, make sure the rigid metal fuel line (the one with the flare nut) is sitting in the filter.
I took a couple of pics, just to help anybody who can't find the filter itself.
I used a Ryco Z441 fuel filter.
It was a pretty straight forward job. The hardest part is just trying to get access to it. If you have huge forearms it could be a real prick of a job.
Tips:
- Depending on the size/shape of your intake pipe, you may not have to remove it to gain access.
- Getting the 14 mm flare nut and the 19 mm banjo bolt off may require a fair bit of force.
- The fuel filter and lines will still have a bit of fuel in them so use paper towels or a rag or something to catch it as you loosen the nuts.
- When you bolt the new filter back onto the firewall, make sure the rigid metal fuel line (the one with the flare nut) is sitting in the filter.
I took a couple of pics, just to help anybody who can't find the filter itself.
I used a Ryco Z441 fuel filter.
- Sahin
- HULK
- Posts: 5518
- Joined: Wed Oct 05, 2011 10:38 pm
- Location: Up to me nuts in boys guts
Re: DIY: How to change your fuel filter
Yeah I had to take my engine out to get to it because of my massive forearms.mr_andersen wrote:Thanks for the write up Vectose.
It was a pretty straight forward job. The hardest part is just trying to get access to it. If you have huge forearms it could be a real prick of a job.
Tips:
- Depending on the size/shape of your intake pipe, you may not have to remove it to gain access.
- Getting the 14 mm flare nut and the 19 mm banjo bolt off may require a fair bit of force.
- The fuel filter and lines will still have a bit of fuel in them so use paper towels or a rag or something to catch it as you loosen the nuts.
- When you bolt the new filter back onto the firewall, make sure the rigid metal fuel line (the one with the flare nut) is sitting in the filter.
I took a couple of pics, just to help anybody who can't find the filter itself.
I used a Ryco Z441 fuel filter.
- Daniel2019
- Oldtimer
- Posts: 7957
- Joined: Thu Jan 12, 2012 12:25 pm
- Location: Sydney!
- Contact:
Re: DIY: How to change your fuel filter
Sahin wrote:Yeah I had to take my engine out to get to it because of my massive forearms.
I fix cars.
Bennoz wrote:I got Bali beli & sharted on my phone. But it was fun
bjk wrote:you old people are no help at all.
- Taz
- Oldtimer
- Posts: 3995
- Joined: Wed Jan 05, 2011 11:50 am
- Location: Your mothers house
- shadowarrior
- Tightarse
- Posts: 2703
- Joined: Thu Oct 27, 2011 4:48 pm
- Location: Gold Coast
Re: DIY: How to change your fuel filter
He did almost take out the engine yesterday on mine.... supposedly there's a Japanese guy out there who has almost same strength if not more than Sahin.
- Sahin
- HULK
- Posts: 5518
- Joined: Wed Oct 05, 2011 10:38 pm
- Location: Up to me nuts in boys guts
Re: DIY: How to change your fuel filter
That bolt was tight! But I still got it undone without a breaker bar
- shadowarrior
- Tightarse
- Posts: 2703
- Joined: Thu Oct 27, 2011 4:48 pm
- Location: Gold Coast
Re: DIY: How to change your fuel filter
What will I do without you mate?
- PHIL069
- Oldtimer
- Posts: 4719
- Joined: Sun Sep 20, 2009 5:00 pm
- Location: Central Coast > South Australia
Re: DIY: How to change your fuel filter
Your arm is a breaker bar!Sahin wrote:That bolt was tight! But I still got it undone without a breaker bar
mikeey01nzl wrote:Hats off to you too Phil for spending so much time on the phone trying to help someone out, your a top man and only a few would've spent so much time. well done!
Daniel2019 wrote:Come on phil, we bonded at the bonfire, lets be honest here...me and phil are besties now...
- Kustom
- Oldtimer
- Posts: 6144
- Joined: Sun Oct 04, 2009 5:00 pm
- Location: Brisbane
-
- Apprentice
- Posts: 34
- Joined: Wed Feb 16, 2011 11:11 pm
Re: DIY: How to change your fuel filter
Just a thought, why remove the back seat?
Cant you just find the fuse and pull that instead?
Would be a hell of a lot easier then pulling the back seat out.
Cant you just find the fuse and pull that instead?
Would be a hell of a lot easier then pulling the back seat out.
- ObsidianRadio
- Oldtimer
- Posts: 2050
- Joined: Sat Jan 21, 2012 4:08 am
- Location: Adelaide, SA
- Contact:
Re: DIY: How to change your fuel filter
The back seat's pretty quick and easy to remove if you think about itclif wrote:Just a thought, why remove the back seat?
Cant you just find the fuse and pull that instead?
Would be a hell of a lot easier then pulling the back seat out.
Jack
Livin' the Slow Life. 1997 GP Version-R | 1995 GS/GR Version-SparkleFairy
http://www.facebook.com/SlowLifeAU
Livin' the Slow Life. 1997 GP Version-R | 1995 GS/GR Version-SparkleFairy
http://www.facebook.com/SlowLifeAU
- Sahin
- HULK
- Posts: 5518
- Joined: Wed Oct 05, 2011 10:38 pm
- Location: Up to me nuts in boys guts
Re: DIY: How to change your fuel filter
Lol no the bottom part of the seat is two clips and you pull it out in less than 4 seconds...
- ObsidianRadio
- Oldtimer
- Posts: 2050
- Joined: Sat Jan 21, 2012 4:08 am
- Location: Adelaide, SA
- Contact:
Re: DIY: How to change your fuel filter
Ejector seatSahin wrote:Lol no the bottom part of the seat is two clips and you pull it out in less than 4 seconds...
Jack
Livin' the Slow Life. 1997 GP Version-R | 1995 GS/GR Version-SparkleFairy
http://www.facebook.com/SlowLifeAU
Livin' the Slow Life. 1997 GP Version-R | 1995 GS/GR Version-SparkleFairy
http://www.facebook.com/SlowLifeAU
- Jase726
- Grease Monkey
- Posts: 112
- Joined: Fri Aug 31, 2012 4:11 am
Re: DIY: How to change your fuel filter
I used a lot of colourful words getting that top bolt out. Thought I was going to tear the bracket off the firewall.
-
- Apprentice
- Posts: 34
- Joined: Wed Feb 16, 2011 11:11 pm
Re: DIY: How to change your fuel filter
LOL ok having done this over the weekend I see why, the fuse box is in japanese lol much easier just rip that back seat out.
Plus that bolt holding the bracket was a bitch!
Plus that bolt holding the bracket was a bitch!
- payaya
- Oldtimer
- Posts: 3670
- Joined: Sat Sep 06, 2003 5:00 pm
Re: DIY: How to change your fuel filter
Just get the filter off, it only drips out only, no need to do all that fuse crap.