General Questions and comments
Moderators: IMC , Club Staff
Bennoz
National President
Posts: 23676 Joined: Fri Jan 21, 2005 6:00 pm
Location: Sydney
Contact:
Post
by Bennoz » Thu Feb 23, 2012 4:48 pm
Stainless... schwanky!
Shhtuart
Forum Moderator
Posts: 1747 Joined: Sun Aug 05, 2007 5:00 pm
Location: Melbourne
Contact:
Post
by Shhtuart » Thu Feb 23, 2012 4:49 pm
I bought some pro shop iida ones a few months ago. Any ideas where I can get the gaskets for them?
Taz
Oldtimer
Posts: 3995 Joined: Wed Jan 05, 2011 11:50 am
Location: Your mothers house
Post
by Taz » Fri Feb 24, 2012 12:02 am
They look like a pretty good pipe design but they are still short as f**k!
Bennoz wrote: Cum gunt it!
Bennoz
National President
Posts: 23676 Joined: Fri Jan 21, 2005 6:00 pm
Location: Sydney
Contact:
Post
by Bennoz » Fri Feb 24, 2012 8:18 am
Shhtuart wrote: I bought some pro shop iida ones a few months ago. Any ideas where I can get the gaskets for them?
Which gasket?
Shhtuart
Forum Moderator
Posts: 1747 Joined: Sun Aug 05, 2007 5:00 pm
Location: Melbourne
Contact:
Post
by Shhtuart » Thu Sep 06, 2012 6:19 pm
Bennoz wrote: Shhtuart wrote: I bought some pro shop iida ones a few months ago. Any ideas where I can get the gaskets for them?
Which gasket?
The one that goes between the block and the headers.
phunkydude
Veteran Mechanic
Posts: 1114 Joined: Sun Mar 14, 2010 6:00 pm
Location: Brisbane
Post
by phunkydude » Thu Sep 06, 2012 8:44 pm
time travel much?
spetz
Oldtimer
Posts: 2915 Joined: Wed Mar 03, 2004 6:00 pm
Post
by spetz » Thu Sep 06, 2012 9:34 pm
Shhtuart wrote: Bennoz wrote: Shhtuart wrote: I bought some pro shop iida ones a few months ago. Any ideas where I can get the gaskets for them?
Which gasket?
The one that goes between the block and the headers.
This would be just the stock exhaust manifold gasket.
Certainly camskill sell it
Bennoz
National President
Posts: 23676 Joined: Fri Jan 21, 2005 6:00 pm
Location: Sydney
Contact:
Post
by Bennoz » Thu Sep 06, 2012 10:30 pm
spetz wrote: Shhtuart wrote: Bennoz wrote: Shhtuart wrote: I bought some pro shop iida ones a few months ago. Any ideas where I can get the gaskets for them?
Which gasket?
The one that goes between the block and the headers.
This would be just the stock exhaust manifold gasket.
Certainly camskill sell it
I bought a couple from Mitsi recently, was a bit dearer, but all good. I'll see if I can scratch up the invoice. I seem to recall them being about $50 a pop as they're made of copper.
Shhtuart
Forum Moderator
Posts: 1747 Joined: Sun Aug 05, 2007 5:00 pm
Location: Melbourne
Contact:
Post
by Shhtuart » Fri Sep 07, 2012 2:48 pm
Cheers guys, the extractors are still sitting in the garage hence the blast from the past
spetz
Oldtimer
Posts: 2915 Joined: Wed Mar 03, 2004 6:00 pm
Post
by spetz » Fri Sep 07, 2012 9:39 pm
Bennoz
National President
Posts: 23676 Joined: Fri Jan 21, 2005 6:00 pm
Location: Sydney
Contact:
Post
by Bennoz » Sun Sep 09, 2012 10:30 pm
Yep, that's each.