Ello - NSW
Moderators: IMC, Club Staff
-
- Apprentice
- Posts: 42
- jedwabna poszewka promocja
- Joined: Sat Jul 25, 2009 5:00 pm
- Location: Castle Hill, 2154, NSW
- Contact:
Ello - NSW
Hi guys.
I've been looking for quite a while at FTO's, and after much deliberation finally took the plunge and bought one yesterday.
Its had quite a lot done too it... both good and bad.
Will post pics soon...
BUT! If any one has a spare windscreen wiper arm (it was ripped off by an angry person), and the front lip of the veilside kit, I will pay top dollar!
It also needs some work done mechanically. Apparently the Front and Rear Rocket gaskets are leaking, and it is due for a new time belt. (if you have any tips on this it would be appreciated!)
Thanks!
~Martin
I've been looking for quite a while at FTO's, and after much deliberation finally took the plunge and bought one yesterday.
Its had quite a lot done too it... both good and bad.
Will post pics soon...
BUT! If any one has a spare windscreen wiper arm (it was ripped off by an angry person), and the front lip of the veilside kit, I will pay top dollar!
It also needs some work done mechanically. Apparently the Front and Rear Rocket gaskets are leaking, and it is due for a new time belt. (if you have any tips on this it would be appreciated!)
Thanks!
~Martin
- dstocks
- National Vice President
- Posts: 9529
- Joined: Fri Jun 24, 2005 5:00 pm
- Location: Utopia
- Contact:
Welcome to the club!. Looking forward to the piccies.
BTW, I can help with the wiper arm.
BTW, I can help with the wiper arm.
Complete FTO (http://www.completefto.com.au/completefto.asp) 
If you are trying to contact me and not getting a quick answer, its because im disorganised. Hassle me and ill get back to you

If you are trying to contact me and not getting a quick answer, its because im disorganised. Hassle me and ill get back to you
- vipfto
- Forum Moderator
- Posts: 4154
- Joined: Mon Oct 29, 2007 5:00 pm
- Location: Adelaide
wttc mate
the gaskets are easy fix around 30 each for part if you can replace yourself
timing belt will cost around 1000 incl labour if you cant do it yourself, just make sure you do waterpump, tensioner etc at the same time
however it may be cheaper to source parts yourself should be around 300ish for all required parts not incl hydrolic tensioner which doesnt always have to be replaced then labour should be around 400 mark
oh and seeing as you have to remove inlet manifold for rocker gaskets may aswell replace the sparkies and plugs if needed

the gaskets are easy fix around 30 each for part if you can replace yourself
timing belt will cost around 1000 incl labour if you cant do it yourself, just make sure you do waterpump, tensioner etc at the same time
however it may be cheaper to source parts yourself should be around 300ish for all required parts not incl hydrolic tensioner which doesnt always have to be replaced then labour should be around 400 mark
oh and seeing as you have to remove inlet manifold for rocker gaskets may aswell replace the sparkies and plugs if needed

FTO GR-TURBO
172KW ATW @ 11PSI
172KW ATW @ 11PSI
-
- Apprentice
- Posts: 42
- Joined: Sat Jul 25, 2009 5:00 pm
- Location: Castle Hill, 2154, NSW
- Contact:
- dstocks
- National Vice President
- Posts: 9529
- Joined: Fri Jun 24, 2005 5:00 pm
- Location: Utopia
- Contact:
Say $30 + postage for both. Can pay by bank deposit. Send me a PM with your address (if you want to go ahead) and well get it underway.
Complete FTO (http://www.completefto.com.au/completefto.asp) 
If you are trying to contact me and not getting a quick answer, its because im disorganised. Hassle me and ill get back to you

If you are trying to contact me and not getting a quick answer, its because im disorganised. Hassle me and ill get back to you
-
- Apprentice
- Posts: 42
- Joined: Sat Jul 25, 2009 5:00 pm
- Location: Castle Hill, 2154, NSW
- Contact:
-
- Apprentice
- Posts: 42
- Joined: Sat Jul 25, 2009 5:00 pm
- Location: Castle Hill, 2154, NSW
- Contact:
-
- Apprentice
- Posts: 42
- Joined: Sat Jul 25, 2009 5:00 pm
- Location: Castle Hill, 2154, NSW
- Contact:
- Supplanter
- Forum Moderator
- Posts: 6420
- Joined: Tue Oct 22, 2002 5:00 pm
- Location: Arizona Bay
- Contact:
-
- Apprentice
- Posts: 42
- Joined: Sat Jul 25, 2009 5:00 pm
- Location: Castle Hill, 2154, NSW
- Contact:
- zuihoujueding
- Oldtimer
- Posts: 1980
- Joined: Thu Aug 31, 2006 5:00 pm
- Location: Sydney
-
- Apprentice
- Posts: 42
- Joined: Sat Jul 25, 2009 5:00 pm
- Location: Castle Hill, 2154, NSW
- Contact:
- zuihoujueding
- Oldtimer
- Posts: 1980
- Joined: Thu Aug 31, 2006 5:00 pm
- Location: Sydney
-
- Apprentice
- Posts: 42
- Joined: Sat Jul 25, 2009 5:00 pm
- Location: Castle Hill, 2154, NSW
- Contact: