stuck in 3rd gear

Got a problem with your FTO? ask about it here

Moderators: IMC, Club Staff

Post Reply
User avatar
col2560
Mechanic
Posts: 434
jedwabna poszewka promocja
Joined: Fri Jun 06, 2008 5:00 pm
Location: seymour, tennessee, usa
Contact:
Contact col2560

stuck in 3rd gear

Post by col2560 »

hi guys,
my tip gearbox is stuck in 3rd gear and the neutral light on the dash is flashing.
any ideas please?

thanks.
Top
User avatar
Bennoz
National President
Posts: 23677
Joined: Fri Jan 21, 2005 6:00 pm
Location: Sydney
Contact:
Contact Bennoz

Post by Bennoz »

Check the error codes

http://www.ftoaustralia.com/modules.php ... ic&t=14667
Top
ftokiwi
Apprentice
Posts: 39
Joined: Mon Jan 21, 2008 6:00 pm
Location: New Zealand-Dorkland

Post by ftokiwi »

just had the same thing. new transmission here :cry:
Top
User avatar
dstocks
National Vice President
Posts: 9529
Joined: Fri Jun 24, 2005 5:00 pm
Location: Utopia
Contact:
Contact dstocks

Post by dstocks »

hmmm, bit of an ominous sign.

Youll need the error codes to determine what is wrong.
Complete FTO (http://www.completefto.com.au/completefto.asp)
    Image
    If you are trying to contact me and not getting a quick answer, its because im disorganised. Hassle me and ill get back to you
    Top
    User avatar
    Storm
    Veteran Mechanic
    Posts: 841
    Joined: Wed Feb 01, 2006 6:00 pm

    Re: stuck in 3rd gear

    Post by Storm »

    col2560 wrote:hi guys,
    my tip gearbox is stuck in 3rd gear and the neutral light on the dash is flashing.
    any ideas please?

    thanks.
    It is normally just a sensor, if its flashing at 1Hz, or overheated fluid if flashing at 2Hz.

    Typically input or output sensor is playing up and an easy fix.

    Bill
    Top
    User avatar
    col2560
    Mechanic
    Posts: 434
    Joined: Fri Jun 06, 2008 5:00 pm
    Location: seymour, tennessee, usa
    Contact:
    Contact col2560

    Post by col2560 »

    drove it today and it was fine, no problem at all. is a faulty input or output sensor likely to be an Intermittent problem?
    Top
    User avatar
    Storm
    Veteran Mechanic
    Posts: 841
    Joined: Wed Feb 01, 2006 6:00 pm

    Post by Storm »

    col2560 wrote:drove it today and it was fine, no problem at all. is a faulty input or output sensor likely to be an Intermittent problem?
    It could be but it will get worse so extract the error codes and see what it is. That way you wont break down on a dark highway somewhere. (unless the bird you're with warrants it)
    Top
    eThix
    Veteran Mechanic
    Posts: 1046
    Joined: Mon Feb 12, 2007 6:00 pm
    Location: Brisbane

    Post by eThix »

    Well my fto would drive fine for a few mins 10mins? and then it would go into limp mode (3rd gear)
    And it was gear box... $1200 fix.
    Top
    User avatar
    col2560
    Mechanic
    Posts: 434
    Joined: Fri Jun 06, 2008 5:00 pm
    Location: seymour, tennessee, usa
    Contact:
    Contact col2560

    Post by col2560 »

    so what was the problem with your g/box? im guessing more than just a sensor?
    Top
    User avatar
    col2560
    Mechanic
    Posts: 434
    Joined: Fri Jun 06, 2008 5:00 pm
    Location: seymour, tennessee, usa
    Contact:
    Contact col2560

    Post by col2560 »

    seems it was only going into limp mode when cold. did a ATF and filter change today and its cured the problem i think.
    Top
    User avatar
    khunjeng
    Oldtimer
    Posts: 4455
    Joined: Mon Oct 24, 2005 5:00 pm
    Location: Melbourne, Victoria

    Post by khunjeng »

    col2560 wrote:seems it was only going into limp mode when cold. did a ATF and filter change today and its cured the problem i think.
    make sure the fuild level is spot on.
    Top
    User avatar
    col2560
    Mechanic
    Posts: 434
    Joined: Fri Jun 06, 2008 5:00 pm
    Location: seymour, tennessee, usa
    Contact:
    Contact col2560

    Post by col2560 »

    fluid level is good, but it is still "limp moding" when cold. after a few km's i just stop and re-start the engine and its fine. so its still a mystery. im going to change the input and output sensors next.
    Top
    Post Reply

    Return to “FTO Help”