Page 1 of 1
headlights not working
Posted: Thu Aug 24, 2006 6:56 pm
by Hobbsie
both went out same time this morning.. dash lights still work so im assuming its the fuse. the fog lights or whatever down the bottom still work too.
however i pulled out every one of the smaller fuses in the engine bay and none seem to be blown?
looking at this diagram
a.) im not sure which one headlights are.. "14. 40A Lamp"?
b.) i cant read the numbers anyway
which fuse should it be?
Posted: Thu Aug 24, 2006 7:05 pm
by Rocco
Thats what i would assume they would be.
Posted: Thu Aug 24, 2006 8:38 pm
by Bennoz
Bingo - its 14
Posted: Thu Aug 24, 2006 9:57 pm
by jonowong
them are the big ones that are bolted in...
they have a little clear plastic lid... but theyre usually fogged up
but u can open that little lid to see the fuse...
how many times have i told u to get out noob
Posted: Thu Aug 24, 2006 9:59 pm
by Hobbsie
my fuse is fine .. guess both my headlights burnt out same time
looks like theyre gonna be a c**t to change!
Posted: Fri Aug 25, 2006 1:41 pm
by johhny
one of my lights stoped working too and its not the bulb.. any ideas guys???
Posted: Fri Aug 25, 2006 11:01 pm
by payaya
put a mutimeter between terminals of bulb, you cannot look at the filament and come to the conclusion the bulb is blown.
Posted: Thu Aug 31, 2006 7:03 pm
by Hobbsie
in the end both my connectors had burnt out.. due to previous owner having 100W bulbs in there
so i replaced the bulbs and wired up some new connectors and all good
Posted: Thu Aug 31, 2006 11:19 pm
by bobz
Where did you get the connectors from?
BobZ
Posted: Fri Sep 01, 2006 7:32 pm
by I8A4RE
Both mine dont work either i buy new bulbs for them then after about 3 weeks drivers stops workin then after another month the passenger side stops workin ive gone through 3 pairs in like 3-4 months any ideas?????
Posted: Sun Sep 03, 2006 9:02 pm
by I8A4RE
i guess not
Posted: Sun Sep 03, 2006 9:23 pm
by Hobbsie
bobz wrote:Where did you get the connectors from?
BobZ
i got an autoelectrician to make me some
18afre: do you make sure not to touch the glass with your fingers when u are installing them? and do you get good quality 55W bulbs?
Posted: Sun Sep 03, 2006 9:53 pm
by khunjeng
Hobbsie wrote:bobz wrote:Where did you get the connectors from?
BobZ
i got an autoelectrician to make me some
18afre: do you make sure not to touch the glass with your fingers when u are installing them? and do you get good quality 55W bulbs?
they are std HB3 and HB4 connectors and u can get these from amny places or wrecks and just cut the old one off. Should take 10min to install if u have a clue, just wire them up the correct way.
As for touching the glass, thats correct the sh*t on your fingers then the heat does some stuff ( was told once) I think it eats into the glass but to tell u the truth I have before and nothing bad happened hehe.
Posted: Sun Sep 03, 2006 11:26 pm
by I8A4RE
yeah i may have touched the glass ill try again this time makin sure not to touch them as for good qaulity i think they were i got them from super cheap about $45 bucks a pair. can u recommend a brand and place to get them??
Posted: Sun Sep 03, 2006 11:34 pm
by khunjeng
just some normal HB3 and HB4s would be ok. Unless u want HID.