FTO AUSTRALIA

UPDATED
Guys need to sell some parts to clear room in my dads shed I have the following
1: rear bar standard has some minor damage no cracks
2: front bar same deal as rear bar
3: standard side skirts
4: boot no struts though
5: bonnet currently has interest will update if doesnt go ahead
6: front quarter panels
7: main dash
8: mivec rocket cover
9: gpx wing
10: normal intake pipe (connects to throttle body
11: rear compartments that side either side of boot
12: the Fto door sills
That is it for now body parts are white I have photo provided on request cheers guys

1: rear bar standard has some minor damage no cracks
2: front bar same deal as rear bar
3: standard side skirts
4: boot no struts though Because Phil took them
5: bonnet currently has interest will update if doesnt go ahead
6: front quarter panels (drivers side has interest ATM as well
7: main dash I will take if it's going to the tip
8: mivec rocket cover I will take if it's going to the tip
9: gpx wing

I might want the 'boat anchor" from the shed before it gets chucked, the one with no compression

What colour ????

ZFL45H1 wrote: I think that's it atm body parts are white I have photo provided on request cheers guys

My bad.....

Wait wait wait. I had dibs on mivec cover

Daniel2019 wrote:Wait wait wait. I had dibs on mivec cover

I wouldn't mind having it for a while to take some measurements off of it. If you are going to pay for it I could hold it for you until we meet again

PHIL069 wrote:

Daniel2019 wrote:Wait wait wait. I had dibs on mivec cover

I wouldn't mind having it for a while to take some measurements off of it. If you are going to pay for it I could hold it for you until we meet again

Oh right of course buddeh!

Whats up with yours? Im just in dire need of it due to my current *ahem* "colour scheme"

Sorry Daniel2019 lol that is correct I forgot u had dibs sorry all urs I'll send a photo of it for u cheers

None of these will be goin to the tip and I assume PHIL069 u mean the engine

ZFL45H1 wrote:Sorry Daniel2019 lol that is correct I forgot you had dibs sorry all urs I'll send a photo of it for you cheers

All good mate. Phil is welcome to grab it for measurements and whatever he needs from it. I will sort it out to grab it from him

Daniel2019 wrote:

PHIL069 wrote:

Daniel2019 wrote:Wait wait wait. I had dibs on mivec cover

I wouldn't mind having it for a while to take some measurements off of it. If you are going to pay for it I could hold it for you until we meet again

Oh right of course buddeh!

Whats up with yours? Im just in dire need of it due to my current *ahem* "colour scheme"

Nothing wrong with mine, but before you colour it I want to paint some water colour on it and take a stamp imprent of the letters on it (will wash off), I also want to measure the letters and I don't want to risk damaging my red paint.
I am going to get a quote to have the letters laser cut out of stainless so after they get painted the stainless letters could be glued on.

ZFL45H1 wrote:None of these will be goin to the tip and I assume PHIL069 you mean the engine

PHIL069 wrote:

Daniel2019 wrote:

PHIL069 wrote:

Daniel2019 wrote:Wait wait wait. I had dibs on mivec cover

I wouldn't mind having it for a while to take some measurements off of it. If you are going to pay for it I could hold it for you until we meet again

Oh right of course buddeh!

Whats up with yours? Im just in dire need of it due to my current *ahem* "colour scheme"

Nothing wrong with mine, but before you colour it I want to paint some water colour on it and take a stamp imprent of the letters on it (will wash off), I also want to measure the letters and I don't want to risk damaging my red paint.
I am going to get a quote to have the letters laser cut out of stainless so after they get painted the stainless letters could be glued on.

All yours bestie! Im in no rush for it

U get photo Daniel2019

I did. Looks to be in decent nic. Cheers.

No worries I didn't clean it either I'll give it a little TLC

Bump