Wheel nuts
Posted: Sat Mar 28, 2009 11:30 am
Just wondering guys, are we 5 stud 1.25 or 1.5 size for the nuts? cause im planning to replace my wheel nuts and not sure about the size, thanks guys
FTO AUSTRALIA
Welcome to the f**king old FTO Australia forums!!
https://www.ftoaustralia.com/v3/
Wheel nuts
Page 1 of 2
Posted: Sat Mar 28, 2009 6:39 pm
12 x 1.25
Posted: Sat Mar 28, 2009 8:39 pm
as above 1.25 I know this as I was just looking into it the other day 
whent to get some blue wheel nuts from Just Japs but they wanted $225 for the full set, But they where a top named brand just cant recall it at this point
whent to get some blue wheel nuts from Just Japs but they wanted $225 for the full set, But they where a top named brand just cant recall it at this point
Posted: Sat Mar 28, 2009 9:03 pm
u guys sure its 1.25? i asked 2 shop on ebay they said its 1.5? e.g http://cgi.ebay.com.au/WHEEL-NUTS-1-5-M ... .m20.l1116
Posted: Sun Mar 29, 2009 9:33 am
yes its def 1.25eddiii wrote:you guys sure its 1.25? i asked 2 shop on ebay they said its 1.5? e.g http://cgi.ebay.com.au/WHEEL-NUTS-1-5-M ... .m20.l1116
Posted: Sun Mar 29, 2009 5:01 pm
ok thanks guys...i shall buy 1.25, if it doesnt fit YOU ALL will chip in for another set for me ^^
Posted: Sun Mar 29, 2009 5:44 pm
haha its confusing sometimes because jap spec mitzy and most other makes are 1.25 however the aus made ones are 1.5 
Posted: Mon Mar 30, 2009 12:49 pm
wahahah...so if i buy it from ebay, i should tell them i want the 1.25 one?
Posted: Mon Mar 30, 2009 2:49 pm
eddiii wrote:wahahah...so if i buy it from ebay, i should tell them i want the 1.25 one?
Posted: Mon Mar 30, 2009 5:54 pm
koolio1234 wrote:eddiii wrote:wahahah...so if i buy it from ebay, i should tell them i want the 1.25 one?
Posted: Mon Mar 30, 2009 6:43 pm
eddiii wrote:wahahah...so if i buy it from ebay, i should tell them i want the 1.25 one?
Posted: Mon Mar 30, 2009 8:26 pm
LOL u guys...okok STOP WITH THOSE FACEPALM lol
Posted: Mon Mar 30, 2009 8:52 pm
better?
Posted: Thu Apr 09, 2009 2:05 pm
alrite i got my nuts and fitted, and the size is 12mm x 1.5rh and 1.25 doesnt fit....do we have the same fto guys? lol
Posted: Thu Apr 09, 2009 2:14 pm
eddiii wrote:alrite i got my nuts and fitted
Sorry, had to.
Posted: Thu Apr 09, 2009 2:36 pm
BAHAHA that mite help things lolMAD-FTO wrote:eddiii wrote:alrite i got my nuts and fitted
Sorry, had to.
Posted: Thu Apr 09, 2009 4:33 pm
someone must have changed studs previously as they are 1.25 standardeddiii wrote:alrite i got my nuts and fitted, and the size is 12mm x 1.5rh and 1.25 doesnt fit....do we have the same fto guys? lol
Posted: Fri Apr 10, 2009 12:28 am
yeah its uncommon but likely that the previous owner/s changed the stud pattern, my last car needed new a new stud pattern and hubs cos the originals were corroding pretty badly. i doubt that's why they changed your stud pattern but there's some reason.vipfto wrote:someone must have changed studs previously as they are 1.25 standardeddiii wrote:alrite i got my nuts and fitted, and the size is 12mm x 1.5rh and 1.25 doesnt fit....do we have the same fto guys? lol
Posted: Fri Apr 10, 2009 12:58 am
does anyone know if they make short locking nuts? (dont quote me madfto )
My front ones fit under my centre caps but my rears are too long, funny as front and back nuts are the same size. They are about 3cm long.... Any shorter ones around?
)My front ones fit under my centre caps but my rears are too long, funny as front and back nuts are the same size. They are about 3cm long.... Any shorter ones around?
Posted: Fri Apr 10, 2009 1:19 am
sorry I just had tojay6 wrote:does anyone know if they make short locking nuts?
My front ones fit under my centre caps but my rears are too long, funny as front and back nuts are the same size. They are about 3cm long.... Any shorter ones around?
l: l: l: l: l: l: l: l: I know, I know, I'll do it myself: