FTO AUSTRALIA

1. Me (ill pull my name off if we get to 10)
2. Aza
3. Rockit
4. d_dan
5.valandis91
6. Topao
7.
8.
9.
10.

I might as well get these since i need to respray my current ones anyway

If you don't want the top vents you can cut them out and fill in, it's not that hard to do.

OK, im about to complicate this now to try and make everyone happy....

I spoke with the fibreglasser about the vents/no vents thing and here is what he said. If we get 15 people, he'll do a mould with interchangeable vents/flat section (same price). This will allow him to pump out guards either with or without top vents. For that option will need 15 people though, not 10.

So, how do we do this. When you put your name down, state your preference next to it and if you are prepared to take a guard with vents if we dont get the 15. This way, we know where we are at.

1. Me (ill pull my name off if we get to 10)
2. Aza ----- vents
3. Rockit
4. d_dan
5.valandis91
6. Topao
7.
8.
9.
10.

1. Me (ill pull my name off if we get to 10)
2. Aza ----- vents
3. Rockit ---- Vent's, but if u get 15, I may change my mind
4. d_dan
5.valandis91
6. Topao
7.
8.
9.
10.

Ummmm....HELLZ YES!

Sexy sexy fenders, i cant wait till when i pull them out for a wide body, would look saweet!

1. Me (ill pull my name off if we get to 10)
2. Aza ----- vents
3. Rockit ---- Vent's, but if you get 15, I may change my mind
4. d_dan
5.valandis91
6. Topao
7. Taz ---- vents in baby!
8.
9.
10.

BTW i am all in for the rear bar group buy if thats going to get started - already got your front bar being put on very soon just need skirts and waiting on my spoiler and im good! (and bonnet if ftosam starts talking to me again) otherwise ill have to source one myself.

Sorry for causing dramas :s
interchangeable vents as in you can change it between vent and non vent? Hows that work?

1. Me (ill pull my name off if we get to 10)
2. Aza ----- vents
3. Rockit ---- Vent's, but if you get 15, I may change my mind
4. d_dan
5.valandis91
6. Topao
7. Taz ---- vents in baby!
8.mosti -- no vents (but if it dsnt get to 15 may change my mind)
9.
10.

Nah, top section of the mould will be interchangeable. So - just choose with or without vents....

I just remembered i have my after market lambo hinges in behind the guards so are you able to get me the dimensions of the side vent I need to know how deep it goes in what the width and height of the vent is and how far forward and up it is positioned so I can sought of make a paper template of it and see if it will hit the hinges

O and when you say you need 15 people now is it still just the first 10 of those 15 that get it cheap

If it fits I'll get a set with no top vents
Thanks

Thats a good question. Im not sure if the offer now extends to the fifteen. Ill have to find out. Tomorrow........

cheers

dstocks

any luck getting the measurments for me yet

Not just yet. I Dont really get a chance to get to this stuff on a weekday usually. From memory, the bottom of the vent is 15cm from the line that is made by the bottom of the door/top of the sideskirts.

1. Me (ill pull my name off if we get to 10)
2. Aza ----- vents
3. Rockit ---- Vent's, but if you get 15, I may change my mind
4. d_dan
5.valandis91
6. Topao
7. Taz ---- vents in baby!
8.mosti -- no vents (but if it dsnt get to 15 may change my mind)
9. AJ -- all the vents!
10.

Come on people!

I'm waiting for the measurements otherwise I would already have my name down

Shenal wrote:I'm waiting for the measurements otherwise I would already have my name down

Haha he must be busy and has totally forgotten

No, havent forgotten. Life has been crazy. Im going to try and get it sorted tonight.

OK,

Top of vent is 6cm below the bottom of the indicator. The bottom of the vent is 13 cm above where the top of the sideskirt would normally sit. The top front of the vent is the deepest part and is 3cm deep. Vent is 17cm high.

Hope this helps.

I'll take a set if i'm in the first 10