Sahin wrote:So we could use magna stepper motors?
RPW Camshaft spec 6A12 MIVEC
Moderators: IMC, Club Staff
- Daniel2019
- Oldtimer
- Posts: 7957
- jedwabna poszewka promocja
- Joined: Thu Jan 12, 2012 12:25 pm
- Location: Sydney!
- Contact:
Re: RPW Camshaft spec 6A12 MIVEC
I fix cars.
Bennoz wrote:I got Bali beli & sharted on my phone. But it was fun
bjk wrote:you old people are no help at all.
- Nath
- Apprentice
- Posts: 68
- Joined: Wed Jan 29, 2014 2:23 am
- Location: Newcastle
Re: RPW Camshaft spec 6A12 MIVEC
If you can't find one at a wrecker I'm pretty sure these are the ones??... http://www.ebay.com.au/itm/MITSUBISHI-M ... 4897.l4275
- Bennoz
- National President
- Posts: 23668
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: RPW Camshaft spec 6A12 MIVEC
No. Very different stroke.Daniel2019 wrote:Sahin wrote:So we could use magna stepper motors?
- spetz
- Oldtimer
- Posts: 2915
- Joined: Wed Mar 03, 2004 6:00 pm
Re: RPW Camshaft spec 6A12 MIVEC
Sahin wrote:So we could use magna stepper motors?
Bennoz wrote:No. Very different stroke.Daniel2019 wrote:Sahin wrote:So we could use magna stepper motors?
When using a Magna TB though, you leave the Magna ISC in right?
- Bennoz
- National President
- Posts: 23668
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
- Nath
- Apprentice
- Posts: 68
- Joined: Wed Jan 29, 2014 2:23 am
- Location: Newcastle
- spetz
- Oldtimer
- Posts: 2915
- Joined: Wed Mar 03, 2004 6:00 pm
Re: RPW Camshaft spec 6A12 MIVEC
Stepper motor = Idle Speed ControlBennoz wrote:ISC?
- Bennoz
- National President
- Posts: 23668
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: RPW Camshaft spec 6A12 MIVEC
Ah, then no. You don't use the Magna stepper. You use the FTO stepper.spetz wrote:Stepper motor = Idle Speed ControlBennoz wrote:ISC?
-
- Oldtimer
- Posts: 1394
- Joined: Wed Jan 19, 2011 11:32 pm
- Location: Perth
- Contact:
Re: RPW Camshaft spec 6A12 MIVEC
Thread revival.
Am I right in thinking that you can't just use the fto stepper in a magna throttle body due to the different plunger hole that it's going in, so do you swap the bottom casing bit from an FTO one and then use an FTO stepper so the whole bottom part of the TB is FTO?
Wondering if this is why rowans car won't idle right as he's using a magna stepper.
Ben...
Am I right in thinking that you can't just use the fto stepper in a magna throttle body due to the different plunger hole that it's going in, so do you swap the bottom casing bit from an FTO one and then use an FTO stepper so the whole bottom part of the TB is FTO?
Wondering if this is why rowans car won't idle right as he's using a magna stepper.
Ben...
- Vectose
- Forum Moderator
- Posts: 3947
- Joined: Sun Nov 28, 2010 8:45 pm
- Location: Newcastle
Re: RPW Camshaft spec 6A12 MIVEC
Yeah, need to swap over the whole lower section. Careful you don't split the gasket.
Bennoz wrote:A whoooole lot 'o jismTechnikhaus wrote:What is in said Bens big penis by the way?
- Bennoz
- National President
- Posts: 23668
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: RPW Camshaft spec 6A12 MIVEC
Yep transfer all FTO bits across, including stepper.
FTO left, Magna right
FTO left, Magna right
-
- Oldtimer
- Posts: 1394
- Joined: Wed Jan 19, 2011 11:32 pm
- Location: Perth
- Contact:
Re: RPW Camshaft spec 6A12 MIVEC
Short term - I've swapped the throttle body and put the fto one back with the fto stepper - lots better, no more stalling.
So i'll do the bottom swap next and put the magna one back with the fto bottom, see how it runs then.
Cheers fellas.
So i'll do the bottom swap next and put the magna one back with the fto bottom, see how it runs then.
Cheers fellas.
- Bennoz
- National President
- Posts: 23668
- Joined: Fri Jan 21, 2005 6:00 pm
- Location: Sydney
- Contact:
Re: RPW Camshaft spec 6A12 MIVEC
Probably need to add some fuel at idle & low rpms. Runs leaner with the bigger TB.