Page 1 of 1

Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 12:31 am
by mr-charisma
I am cleaning out the garage and have quite a few things for sale;

Whiteline Front Strut brace - Brand new never fitted $160
Image

Whiteline Rear Strut brace - Near new $160
Image

2.5" "Zetti" brand Hi Flow 200CPSI Metal Cat - Brand new never fitted $140
Image

2.5 Inch CAT Back Fujitsubo Stainless Steel Mandrel Bent exhaust - used GC $800 ONO
Image
Image

Mivec Air Fuel Controller "Field" brand - Used GC $60
Image

Unichip Type A - Good for about 10-20kw power increase I think, but there should be plenty of posts about results if you search through the forum $250 - FIRM
Image

Alpine CDA-9887 Head Unit - Audiophile Quality! - New in Box $350 Or nearest reasonable offer (Awesome unit .. if it doesn't sell I'll be using it in my setup)
http://www.alpine.com.au/showItem.php?item_id=40
Image

Alpine V12 AMP - MRV-F345 - brand new in box, never used - $250 ONO
Description:
The V12 Amplifier series feature the same high-grade power transistors and 3-stage Darlington circuit as the premium Alpine F#1 Status amplifier. With the MRV-F345, you don't have to worry about your amp overheating or shutting down at high power levels, thanks to an extremely effective thermal management system. V12 Amplifiers not only allow better channel separation for improved sound imaging and staging, they come with a sleek silver design with blue LCD information display (voltage, current, temperature, etc.), This is a flexible amp addition to complete any system! The MRV-F345 is compatible with the amplifier link unit. Now you can connect any amplifier link ready 2005 head unit to the MRV-F345 (KCE-511M required).

Audio SystemSignal-To-Noise Ratio 96 dB
Continuous Power / Channel Qty 75 Watts x 4
Amplifier Output Details 75 Watt - 4 Ohm - 20 - 20000 Hz - THD 0.3% - 14.4V DC - 4 channel(s) ¦ 150 Watt - 2 Ohm - 20 - 20000 Hz - THD 1.0% - 14.4V DC - 4 channel(s)
Image

Braided Brake Lines -Brand new never fitted $100

FTO 'GR' Stock MAF (Mass Air Flow) Unit - OFFERS
Image

FTO Horn - OFFERS
Image

Muffler Exhaust Tip - OFFERS
Image

Pod Air Filter - OFFERS
Image


Pickup available from Brisbane or Gold Coast area - additional costs if posting
Please PM with any questions :)

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 6:41 am
by Sahin
Dubs on brake lines

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 8:36 am
by silverGPX
hmmmm when funds allow


Sent from my iPhone using Tapatalk

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 9:12 am
by ZFL45H1
silverGPX wrote:hmmmm when funds allow

+1
Interested in rear strut brace

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 10:50 am
by den0va
Interestged in front and rear strut braces... Of course that is if ZFL45H falls through with the rear, if so I'll take the front. :D Funds are ready whenever...

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 3:11 pm
by ZFL45H1
Mate take both iv had a change of plans and funds won't be ready anytime soon for it so all yours champ

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 3:12 pm
by mr-charisma
silverGPX wrote:hmmmm when funds allow


Sent from my iPhone using Tapatalk
I'll just put you down for the lot then :lol:

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 3:24 pm
by mr-charisma
den0va wrote:Interestged in front and rear strut braces... Of course that is if ZFL45H falls through with the rear, if so I'll take the front. :D Funds are ready whenever...
PM'd

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 3:25 pm
by Sahin
Pm me about brake lines can pickup from Brisbane and are they fronts or rears or both?

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 5:30 pm
by mr-charisma
Sahin wrote:Pm me about brake lines can pickup from Brisbane and are they fronts or rears or both?
PM'd

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 7:57 pm
by PHIL069
mr-charisma wrote:Mivec Air Fuel Controller "Field" brand - Used GC $60
Image
Is this any good?
I have done some research.....
Would tricking the MAP sensor to allow moar fuel make the engine run too rich, in turn damaging the bores/pistons/valves?
Does changing MIVEC cut in point to a lower RPM actually give quicker or slower acceleration, and does it lower the RPM upper limit (red line)?
Does it come with wire harness and instructions?

Re: Loads of Aftermarket Parts for Sale

Posted: Wed Oct 17, 2012 9:38 pm
by Taz
It has been researched, and proven that Mitsubishi got it right the first time round. 5500 is the ideal mivec kick in, any less amd you'll lose power.

also - no it wont lower the RPM limit when you lower the mivec - mivec doesnt only go for a specific RPM band, it just kicks in when it is told to and stops when it is told to :lol:
It will probably trick the engine into thinking that it is running rich and lean at the same time - so as well as more fuel it will tell it to let more air through as well? hell i dunno im just taking a wild guess here

Re: Loads of Aftermarket Parts for Sale

Posted: Thu Oct 18, 2012 4:39 pm
by mr-charisma
Taz wrote:It has been researched, and proven that Mitsubishi got it right the first time round. 5500 is the ideal mivec kick in, any less amd you'll lose power.

also - no it wont lower the RPM limit when you lower the mivec - mivec doesnt only go for a specific RPM band, it just kicks in when it is told to and stops when it is told to :lol:
It will probably trick the engine into thinking that it is running rich and lean at the same time - so as well as more fuel it will tell it to let more air through as well? hell i dunno im just taking a wild guess here
Correct, not recommended to change the Mivec point, but it does give some additional tuning options for Air/Fuel Control which can come in quite handy :)

Re: Loads of Aftermarket Parts for Sale

Posted: Thu Oct 18, 2012 5:03 pm
by ZFL45H1
Would it be useful in a low boosted turbo setup

Re: Loads of Aftermarket Parts for Sale

Posted: Thu Oct 18, 2012 5:57 pm
by mr-charisma
ZFL45H1 wrote:Would it be useful in a low boosted turbo setup
nah bud, you'll need something a bit beefier for a turbo setup
*edit* .. Unichip will do the job on a mild turbo install, boost control can be handled by an addon module

Re: Loads of Aftermarket Parts for Sale

Posted: Fri Oct 19, 2012 12:16 pm
by Taz
silverGPX wrote:hmmmm when funds allow


Sent from my iPhone using Tapatalk
1cf3838c.gif
1cf3838c.gif (354.26 KiB) Viewed 1096 times

Re: Loads of Aftermarket Parts for Sale

Posted: Sat Oct 27, 2012 9:02 pm
by Sahin
I'll offer $600 for the exhaust

Re: Loads of Aftermarket Parts for Sale

Posted: Sun Oct 28, 2012 12:05 am
by mr-charisma
I can do the full Exhaust system + the Cat converter for $800

Re: Loads of Aftermarket Parts for Sale

Posted: Sun Oct 28, 2012 12:07 am
by den0va
Strut braces Front and Rear - SOLD :D

Re: Loads of Aftermarket Parts for Sale

Posted: Tue Oct 30, 2012 5:59 pm
by mr-charisma
*bump*

i also have this for sale new, never fitted (pre-primed in black, not white as in picture);

Image

Offers..