Bennoz 6A13 Conversion

[aza013]

Looking good Ben .
Just one thing, stock up on cans/bottles of coke to keep in the car .

[Bennoz]

Ben are you bored

Gotta make use of Step son no#1's pile of crap in my garage

[Astron_Boy]

Ben are you bored

Gotta make use of Step son no#1's pile of crap in my garage

Gotten used to saying that yet?

[Bennoz]

Ben are you bored

Gotta make use of Step son no#1's pile of crap in my garage

Gotten used to saying that yet?

Rolls off the tongue pretty good now

[Bennoz]

Had her all dyno'ed up again yesterday, Was 212kws when I first rolled up (this is on Envys dyno, not Todas) and was 224kws when done. So the bigger TB was good for 12kws

As a result of the bigger TB, it was running super lean below 3,500rpm. I also had a couple of flat spots & an annoying jerk that happened at about 2,500rpm when you lightly get off then back on the throttle, but a quick fiddle with the injector phase angles sorted that out. Also dialled in some more timing up top, so it doesn't drop off as bad at around 6500-7000k when it runs off cam range. I do have about a pound, pound & a half boost loss thanks to the addition of the blow off valve, but I'm told that's normal. Unfortunately my little tubs can't be wound up any further to compensate.

Forgot to even grab a dyno printout, its done so god damned many lol

And just to say thank you to me, it spat the PS/AC belt on the way home

[Astron_Boy]

And just to say thank you to me, it spat the PS/AC belt on the way home

lol.

Nice figure and good to see what the TB gave out.

[aza013]

Not bad at all .

[AJ]

1/4 mile run soon?

[Shane001]

224kw = 300hp

[Bennoz]

300hp, true!

Yeah be up for a 1/4 mile for sure. Last 3 times I've gone to go, its rained lol. And I kinda like those nights where it rains a bit, then clears up, cause there's no one there & you get heaps of runs in!

[Astron_Boy]

300hp FTO!
Definitely a nice title.

[Shane001]

Traction's gonna be a bitch though

Better get yourself a set of slicks

[Astron_Boy]

How many of the Leggu boys are on to doing the TB upgrade I wonder! lol.

Meanwhile, definitely not a factory bolt on job.

[spetz]

Great work there Bennoz

What kind of 400m runs have you done previously?

[Bennoz]

Traction's gonna be a bitch though

Better get yourself a set of slicks

*Builds a spare gearbox*

How many of the Leggu boys are on to doing the TB upgrade I wonder! lol.

Meanwhile, definitely not a factory bolt on job.

Actually, the thread I started over on ozvr4 went on for pages The bigger TB was available apparently on the facelifted, blah blah blah, series blah model of the Leggy from the factory.

What kind of 400m runs have you done previously?

None with this setup, last run I did was with the gas on the GR motor, ran a 14.9.

[Bennoz]

Figured out what caused the belt spit, idler pulley almost seized. Finally figured out how to press the bearing out rather than having to replace the whole thing

[I8A4RE]

So whats been happening in here?

[aza013]

A lot you would have about 20+ pages to get up to speed with, so you best start reading lol.

[spetz]

Great work Ben.
What is the cost difference between getting a hole new setup versus just the bearing?

[Bennoz]

Went to both my bearing guys & neither could help me lol. Its a proprietary bearing made by Koyo for Misti. So I'm getting a quote on a new one from Ralliart NZ.

Mitsi Australia want $170 & Camskill dont even list them (unless I'm blind)