HKS FTO

Post by **Bennoz** » Mon Jan 17, 2011 9:29 pm

Supplanter wrote:Look through Scracy's old posts:
search.php?keywords=&terms=all&author=s ... mit=Search

rock_it wrote:I am betting that AJ's is a GT28

Right you both are!

Scracy from way back in October of 2003 wrote:Garret t28bb hi flowed

AJ · Post by AJ » Mon Jan 17, 2011 9:44 pm

Thanks for the tips guys. I'll take this back to my blog now rather than hack Bens.

Post by **Bennoz** » Mon Jan 17, 2011 9:46 pm

Use the mod tools mate, you can actually cut this from here & add it to your thread

AJ · Post by AJ » Mon Jan 17, 2011 9:54 pm

contiuned from Bens blog...

Thanks to Supplanter I've found this topic viewtopic.php?f=22&t=3834&hilit=+turbo
which tells me that the engine is running stock internals. This is very good to know because up until now, I wasn't sure.

Envy was sure that it must have had forged internals because when I first took it to him it was running so lean that it should have blown up. He'd never seen a stock engine run so lean and no blow up. 1-0 to Mitsubishi.

So I'll ring around and get some estimates on reconditioning the turbo (thanks to Bennoz for the numbers). As for getting it to the repairers, is it easy to take off? Is it really an AJ kind of a job?

Do any evo's run a T28? I might be able to source one fairly cheaply (~$500)

When I got the exhaust made, they were very nervous about the heat because the size of the pipes going to the turbo and out was getting close to the fuel lines. They suggested moving the fuel filter and heat shielding as much as I could. This would be another DIY day job.

It would be great to get as much as this done ready for the bonfire in April.

Post by **I8A4RE** » Tue Jan 18, 2011 10:55 am

So I'll ring around and get some estimates on reconditioning the turbo (thanks to Bennoz for the numbers). As for getting it to the repairers, is it easy to take off? Is it really an AJ kind of a job? - It is relatively easy job mate but it is going to be fiddly as hell.

Do any evo's run a T28? I might be able to source one fairly cheaply (~$500) As far as I am aware they dont. You could get yours rebuilt for not much more than that or brand new as per my email

When I got the exhaust made, they were very nervous about the heat because the size of the pipes going to the turbo and out was getting close to the fuel lines. They suggested moving the fuel filter and heat shielding as much as I could. This would be another DIY day job. I suggest if you are pulling out your turbo do the fuel filter re location then (as per my phone call)

Gholdwayne · Post by **Gholdwayne** » Tue Jan 18, 2011 1:22 pm

If the relocation of the fuel filter happens on a DIY day, could get a hand in doing the same for mine?

bass_twitch · Post by **bass_twitch** » Tue Jan 18, 2011 1:27 pm

Gholdwayne wrote:If the relocation of the fuel filter happens on a DIY day, could get a hand in doing the same for mine?

+1

Actually we should make a Fuel Filter DIY day... haha

Gholdwayne · Post by **Gholdwayne** » Tue Jan 18, 2011 1:38 pm

bass_twitch wrote:
Gholdwayne wrote:If the relocation of the fuel filter happens on a DIY day, could get a hand in doing the same for mine?
+1

Actually we should make a Fuel Filter DIY day... haha

I reckon so too! Make that a Fuel Filter Relocation DIY Day!! I've been told im running rich since black smoke is seen from my exhaust and my mileage of daily commutes only go as far as 450, so maybe those things are fuel filter problems... Im eager to see the innards of my fuel filter though!

Then again, with the running rich thing, Im thinking a haltech + tune would fix that.. Im going to get a 100,000k service done first before I put the haltech in. Then thats my power mods done! I will be happy with that...

Post by **Bennoz** » Tue Jan 18, 2011 2:01 pm

*shudders*

Well, we aint doing sh*t till I have the use of my right fore finger back!

Gholdwayne · Post by **Gholdwayne** » Tue Jan 18, 2011 2:09 pm

Bennoz wrote:*shudders*

Well, we aint doing sh*t till I have the use of my right fore finger back!

I like that, the pres cant do sh*t, everyone cant do sh*t...

Post by **aza013** » Tue Jan 18, 2011 2:35 pm

Well when it comes down to it who will end up doing the work?

Post by **Bennoz** » Tue Jan 18, 2011 2:59 pm

lol, I'll be back on deck in a couple of weeks. Been trying to work on my seal rails, but finding left handed drilling & screwing super difficult

bass_twitch · Post by **bass_twitch** » Tue Jan 18, 2011 5:11 pm

Bennoz wrote:finding left handed drilling & screwing super difficult

rock_it · Post by **rock_it** » Tue Jan 18, 2011 5:52 pm

Bennoz wrote: Been trying to work on my seal rails

Typing fail..

Post by **Bennoz** » Tue Jan 18, 2011 9:02 pm

Yeah that aint easy either!

rock_it · Post by **rock_it** » Tue Jan 18, 2011 9:41 pm

Bennoz wrote:Yeah that aint easy either!

I could imagine..

Post by **I8A4RE** » Wed Jan 19, 2011 11:23 am

Bennoz wrote:Yeah that aint easy either!

Maybe we need to put in for this keyboard for you?

Astron_Boy · Post by **Astron_Boy** » Wed Jan 19, 2011 4:19 pm

Keep forgetting about this thread.

Did we do the headlights back last year at the late bonfire?
Why are they blue again, or have I missed a post..

Post by **aza013** » Wed Jan 19, 2011 4:46 pm

Yep you mist a post

And yes they are still black.

Astron_Boy · Post by **Astron_Boy** » Wed Jan 19, 2011 5:07 pm

Oh, so it's just an old shot.

Good-o then

edit: Oh, read the post above the pic and it all makes sense now.

FTO AUSTRALIA

HKS FTO

Re: Bennoz 6A13 Conversion

Re: Bennoz 6A13 Conversion

Re: Bennoz 6A13 Conversion

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO

Re: HKS FTO