Cusco Comp 2 Coilovers
Moderators: IMC, Club Staff
-
- 9.5"
- Posts: 6793
- jedwabna poszewka promocja
- Joined: Tue Oct 13, 2009 5:00 pm
Cusco Comp 2 Coilovers
Hi there,
Selling my Cusco Comp 2 Coilovers front and rear, it is my belief that these are non base height adjustable.
However you can really dump your car on these things.
Can't see any leaks, a few scuffs here in there but in good condition.
Looking at 470 + postage.
Located in qld.
Best to get these installed and setup by a suspension shop.
Selling my Cusco Comp 2 Coilovers front and rear, it is my belief that these are non base height adjustable.
However you can really dump your car on these things.
Can't see any leaks, a few scuffs here in there but in good condition.
Looking at 470 + postage.
Located in qld.
Best to get these installed and setup by a suspension shop.
Last edited by silverGPX on Fri Jun 14, 2013 5:30 pm, edited 1 time in total.
- Technikhaus
- Oldtimer
- Posts: 3656
- Joined: Wed Dec 28, 2011 4:45 pm
- Location: Dunedin - NZ
- Contact:
Re: Cusco Coilovers
I would be tempted if it were not for requiring a Cert to get them installed
Man '96 FTO GPX
Man '89 Legacy RS Rally car
Man '90 MR2 GT
Auto '08 Fairmont Ghia
Man '89 Legacy RS Rally car
Man '90 MR2 GT
Auto '08 Fairmont Ghia
-
- 9.5"
- Posts: 6793
- Joined: Tue Oct 13, 2009 5:00 pm
Re: Cusco Coilovers
Also would like to say these are ONO.
But not after low balling..
But not after low balling..
- bass_twitch
- Oldtimer
- Posts: 2423
- Joined: Thu May 27, 2010 3:37 pm
- Location: Western Sydney, NSW
-
- Apprentice
- Posts: 88
- Joined: Mon May 27, 2013 3:05 pm
- Location: Melbourne, VIC
Re: Cusco Comp 2 Coilovers
maybe interested, how old are they?silverGPX wrote:Hi there,
Selling my Cusco Comp 2 Coilovers front and rear, it is my belief that these are non base height adjustable.
However you can really dump your car on these things.
Can't see any leaks, a few scuffs here in there but in good condition.
Looking at 470 + postage.
Located in qld.
Best to get these installed and setup by a suspension shop.
- fraz91
- Hair-do
- Posts: 881
- Joined: Sun Jan 17, 2010 6:00 pm
- Location: 4wding over you, Sydney
Re: Cusco Comp 2 Coilovers
GLWS mate.
You going back to standard lowered springs and struts?
You going back to standard lowered springs and struts?
I'll have an FTO one day... i swear!
until then:
1. 2001 Merc-Benz A160 (porta-loo on wheels)
2. 2007 Peugeot 307 TDi (more fun than you'd expect)
3. [url=ttp://ftoaustralia.com/v3/viewtopic.php?f=29&t=25373]2009 Mitsubishi Triton Di-D (a monster in its own right)[/url]
4. 1992 Nissan NX Coupe (club car and project car)
5. 1996 Holden SB Barina - "The Nugget"
6. 1996 Jeep XJ Cherokee Sport - The Budget Build
7. 2010 Toyota Landcruiser 76 Series - V8 Goodness... - Build coming soon.
8. 1990 Audi 90 manual - The delightfully dignified daily driver
until then:
1. 2001 Merc-Benz A160 (porta-loo on wheels)
2. 2007 Peugeot 307 TDi (more fun than you'd expect)
3. [url=ttp://ftoaustralia.com/v3/viewtopic.php?f=29&t=25373]2009 Mitsubishi Triton Di-D (a monster in its own right)[/url]
4. 1992 Nissan NX Coupe (club car and project car)
5. 1996 Holden SB Barina - "The Nugget"
6. 1996 Jeep XJ Cherokee Sport - The Budget Build
7. 2010 Toyota Landcruiser 76 Series - V8 Goodness... - Build coming soon.
8. 1990 Audi 90 manual - The delightfully dignified daily driver
Astron_Boy wrote:No correction needed Gen Y, you are correct.
Bennoz wrote:My rubbing happens on the inside.
-
- Apprentice
- Posts: 88
- Joined: Mon May 27, 2013 3:05 pm
- Location: Melbourne, VIC
Re: Cusco Comp 2 Coilovers
im not too sure actually lol... couldn't find much information online.. are they really low?fraz91 wrote:GLWS mate.
You going back to standard lowered springs and struts?
- destinationtoby
- Broke it
- Posts: 3503
- Joined: Sat Nov 24, 2012 11:05 pm
- Location: mid north coast
Re: Cusco Comp 2 Coilovers
bryan wrote:im not too sure actually lol... couldn't find much information online.. are they really low?fraz91 wrote:GLWS mate.
You going back to standard lowered springs and struts?
I think he was talking to silverGPX
Because nothing is faster than a p plater in a commodore.....
except maybe a p plater on a unicorn
except maybe a p plater on a unicorn
FTOcrazy273 wrote: Destinationtoby probably has one of THE best FTO's on the forum I never get tired of looking at his pics! Good work mate!
- Vectose
- Forum Moderator
- Posts: 3952
- Joined: Sun Nov 28, 2010 8:45 pm
- Location: Newcastle
Re: Cusco Comp 2 Coilovers
That was directed at SilverGPX, not yourself.bryan wrote:im not too sure actually lol... couldn't find much information online.. are they really low?fraz91 wrote:GLWS mate.
You going back to standard lowered springs and struts?
The concern is not about height with coilovers (as most are adjustable)
The concern is with the harshness of the ride with coilovers. I would not recommend coilovers for a daily drive. (Especially if the roads where you live are rough)
A set of KYB shocks and some lowered springs is the perfect balance between comfort and handling.
Bennoz wrote:A whoooole lot 'o jismTechnikhaus wrote:What is in said Bens big penis by the way?
- fraz91
- Hair-do
- Posts: 881
- Joined: Sun Jan 17, 2010 6:00 pm
- Location: 4wding over you, Sydney
Re: Cusco Comp 2 Coilovers
Coilovers are good because you can set the height of them yourself by either increasing or decreasing the pre-load on the spring, thus lifting or lowering the vehicle. Coil-overs that are body-adjustable as well are made to suit multiple vehicles, and as such the overall length should be adjusted to be the same as the OE struts/shocks.bryan wrote:im not too sure actually lol... couldn't find much information online.. are they really low?fraz91 wrote:GLWS mate.
You going back to standard lowered springs and struts?
The common misconception is that you wind the pre-load you want in, and then adjust the height through the body. The problem with this is that if you don't wind enough pre-load on, you'll be bottoming out the strut and giving yourself a really harsh and uncomfortable ride. What you need to do is adjust the body and overall length to be the same, and then adjust the height by moving the coil-seat up or down. If it's still too stiff after that, and there's no adjustment in the shocks themselves, then you need to look at using a coil with a lower spring rate.
edit- Coil-overs can provide a ride similarly comfortable to that of lowered coils with KYB's, as long as they're set up correctly. I know this, because I've done it to an S15 at work when changing one set of coil-overs to another and the originals weren't set up correctly.
I'll have an FTO one day... i swear!
until then:
1. 2001 Merc-Benz A160 (porta-loo on wheels)
2. 2007 Peugeot 307 TDi (more fun than you'd expect)
3. [url=ttp://ftoaustralia.com/v3/viewtopic.php?f=29&t=25373]2009 Mitsubishi Triton Di-D (a monster in its own right)[/url]
4. 1992 Nissan NX Coupe (club car and project car)
5. 1996 Holden SB Barina - "The Nugget"
6. 1996 Jeep XJ Cherokee Sport - The Budget Build
7. 2010 Toyota Landcruiser 76 Series - V8 Goodness... - Build coming soon.
8. 1990 Audi 90 manual - The delightfully dignified daily driver
until then:
1. 2001 Merc-Benz A160 (porta-loo on wheels)
2. 2007 Peugeot 307 TDi (more fun than you'd expect)
3. [url=ttp://ftoaustralia.com/v3/viewtopic.php?f=29&t=25373]2009 Mitsubishi Triton Di-D (a monster in its own right)[/url]
4. 1992 Nissan NX Coupe (club car and project car)
5. 1996 Holden SB Barina - "The Nugget"
6. 1996 Jeep XJ Cherokee Sport - The Budget Build
7. 2010 Toyota Landcruiser 76 Series - V8 Goodness... - Build coming soon.
8. 1990 Audi 90 manual - The delightfully dignified daily driver
Astron_Boy wrote:No correction needed Gen Y, you are correct.
Bennoz wrote:My rubbing happens on the inside.
-
- Apprentice
- Posts: 88
- Joined: Mon May 27, 2013 3:05 pm
- Location: Melbourne, VIC
Re: Cusco Comp 2 Coilovers
Vectose wrote:That was directed at SilverGPX, not yourself.bryan wrote:im not too sure actually lol... couldn't find much information online.. are they really low?fraz91 wrote:GLWS mate.
You going back to standard lowered springs and struts?
The concern is not about height with coilovers (as most are adjustable)
The concern is with the harshness of the ride with coilovers. I would not recommend coilovers for a daily drive. (Especially if the roads where you live are rough)
A set of KYB shocks and some lowered springs is the perfect balance between comfort and handling.
ahh i see...any kyb shocks and lowered springs would fit my FTO? my shocks may need replacing soon as over 140k without replacing (told by the mechanic). quoted 1000 just to change my shocks. i guess thats the market rate?
-
- Apprentice
- Posts: 88
- Joined: Mon May 27, 2013 3:05 pm
- Location: Melbourne, VIC
Re: Cusco Comp 2 Coilovers
fraz91 wrote:Coilovers are good because you can set the height of them yourself by either increasing or decreasing the pre-load on the spring, thus lifting or lowering the vehicle. Coil-overs that are body-adjustable as well are made to suit multiple vehicles, and as such the overall length should be adjusted to be the same as the OE struts/shocks.bryan wrote:im not too sure actually lol... couldn't find much information online.. are they really low?fraz91 wrote:GLWS mate.
You going back to standard lowered springs and struts?
The common misconception is that you wind the pre-load you want in, and then adjust the height through the body. The problem with this is that if you don't wind enough pre-load on, you'll be bottoming out the strut and giving yourself a really harsh and uncomfortable ride. What you need to do is adjust the body and overall length to be the same, and then adjust the height by moving the coil-seat up or down. If it's still too stiff after that, and there's no adjustment in the shocks themselves, then you need to look at using a coil with a lower spring rate.
edit- Coil-overs can provide a ride similarly comfortable to that of lowered coils with KYB's, as long as they're set up correctly. I know this, because I've done it to an S15 at work when changing one set of coil-overs to another and the originals weren't set up correctly.
damn sounds too complicated for me to handle...lol
- Vectose
- Forum Moderator
- Posts: 3952
- Joined: Sun Nov 28, 2010 8:45 pm
- Location: Newcastle
Re: Cusco Comp 2 Coilovers
So you are saying a set of coilovers with double the spring rate of lowered springs will have the same ride comfort?fraz91 wrote:Coilovers are good because you can set the height of them yourself by either increasing or decreasing the pre-load on the spring, thus lifting or lowering the vehicle. Coil-overs that are body-adjustable as well are made to suit multiple vehicles, and as such the overall length should be adjusted to be the same as the OE struts/shocks.bryan wrote:im not too sure actually lol... couldn't find much information online.. are they really low?fraz91 wrote:GLWS mate.
You going back to standard lowered springs and struts?
The common misconception is that you wind the pre-load you want in, and then adjust the height through the body. The problem with this is that if you don't wind enough pre-load on, you'll be bottoming out the strut and giving yourself a really harsh and uncomfortable ride. What you need to do is adjust the body and overall length to be the same, and then adjust the height by moving the coil-seat up or down. If it's still too stiff after that, and there's no adjustment in the shocks themselves, then you need to look at using a coil with a lower spring rate.
edit- Coil-overs can provide a ride similarly comfortable to that of lowered coils with KYB's, as long as they're set up correctly. I know this, because I've done it to an S15 at work when changing one set of coil-overs to another and the originals weren't set up correctly.
Bennoz wrote:A whoooole lot 'o jismTechnikhaus wrote:What is in said Bens big penis by the way?
- destinationtoby
- Broke it
- Posts: 3503
- Joined: Sat Nov 24, 2012 11:05 pm
- Location: mid north coast
Re: Cusco Comp 2 Coilovers
bryan wrote:
ahh i see...any kyb shocks and lowered springs would fit my FTO? my shocks may need replacing soon as over 140k without replacing (told by the mechanic). quoted 1000 just to change my shocks. i guess thats the market rate?
No u have to get the right part number for the shocks.
$1000 for 4 new shocks and fitted? Abit steep I think
U can order the kyb ones directly from them, forgotten what the prices are though
Because nothing is faster than a p plater in a commodore.....
except maybe a p plater on a unicorn
except maybe a p plater on a unicorn
FTOcrazy273 wrote: Destinationtoby probably has one of THE best FTO's on the forum I never get tired of looking at his pics! Good work mate!
- destinationtoby
- Broke it
- Posts: 3503
- Joined: Sat Nov 24, 2012 11:05 pm
- Location: mid north coast
Re: Cusco Comp 2 Coilovers
Forsalethreadgonewild
Because nothing is faster than a p plater in a commodore.....
except maybe a p plater on a unicorn
except maybe a p plater on a unicorn
FTOcrazy273 wrote: Destinationtoby probably has one of THE best FTO's on the forum I never get tired of looking at his pics! Good work mate!
- fraz91
- Hair-do
- Posts: 881
- Joined: Sun Jan 17, 2010 6:00 pm
- Location: 4wding over you, Sydney
Re: Cusco Comp 2 Coilovers
No, and that's the main reason people find coil-overs to be so harsh. Spring rate is relative to weight, so if you over-spring the vehicle then of course it's going to be uncomfortable. That's like using a heavy duty spring in a car with no weight, it'll ride like crap and skip all over the road.Vectose wrote:So you are saying a set of coilovers with double the spring rate of lowered springs will have the same ride comfort?fraz91 wrote:Coil-over education blah blahbryan wrote:im not too sure actually lol... couldn't find much information online.. are they really low?fraz91 wrote:GLWS mate.
You going back to standard lowered springs and struts?
I'll have an FTO one day... i swear!
until then:
1. 2001 Merc-Benz A160 (porta-loo on wheels)
2. 2007 Peugeot 307 TDi (more fun than you'd expect)
3. [url=ttp://ftoaustralia.com/v3/viewtopic.php?f=29&t=25373]2009 Mitsubishi Triton Di-D (a monster in its own right)[/url]
4. 1992 Nissan NX Coupe (club car and project car)
5. 1996 Holden SB Barina - "The Nugget"
6. 1996 Jeep XJ Cherokee Sport - The Budget Build
7. 2010 Toyota Landcruiser 76 Series - V8 Goodness... - Build coming soon.
8. 1990 Audi 90 manual - The delightfully dignified daily driver
until then:
1. 2001 Merc-Benz A160 (porta-loo on wheels)
2. 2007 Peugeot 307 TDi (more fun than you'd expect)
3. [url=ttp://ftoaustralia.com/v3/viewtopic.php?f=29&t=25373]2009 Mitsubishi Triton Di-D (a monster in its own right)[/url]
4. 1992 Nissan NX Coupe (club car and project car)
5. 1996 Holden SB Barina - "The Nugget"
6. 1996 Jeep XJ Cherokee Sport - The Budget Build
7. 2010 Toyota Landcruiser 76 Series - V8 Goodness... - Build coming soon.
8. 1990 Audi 90 manual - The delightfully dignified daily driver
Astron_Boy wrote:No correction needed Gen Y, you are correct.
Bennoz wrote:My rubbing happens on the inside.
- Vectose
- Forum Moderator
- Posts: 3952
- Joined: Sun Nov 28, 2010 8:45 pm
- Location: Newcastle
Re: Cusco Comp 2 Coilovers
What spring rate would you recommend for an FTO then?
Bennoz wrote:A whoooole lot 'o jismTechnikhaus wrote:What is in said Bens big penis by the way?
- fraz91
- Hair-do
- Posts: 881
- Joined: Sun Jan 17, 2010 6:00 pm
- Location: 4wding over you, Sydney
Re: Cusco Comp 2 Coilovers
To be honest, without testing a factory spring I'd have no idea. If people are happy with the Lovells spring rates then I'm sure I'd be able to "persuade" them to lend me one for testing.Vectose wrote:What spring rate would you recommend for an FTO then?
Alternatively, contact lovells and ask them yourself, then just select the closest spring rate to that you want. Firmer if you want a sportier ride, softer if you're after comfort over handling.
I'll have an FTO one day... i swear!
until then:
1. 2001 Merc-Benz A160 (porta-loo on wheels)
2. 2007 Peugeot 307 TDi (more fun than you'd expect)
3. [url=ttp://ftoaustralia.com/v3/viewtopic.php?f=29&t=25373]2009 Mitsubishi Triton Di-D (a monster in its own right)[/url]
4. 1992 Nissan NX Coupe (club car and project car)
5. 1996 Holden SB Barina - "The Nugget"
6. 1996 Jeep XJ Cherokee Sport - The Budget Build
7. 2010 Toyota Landcruiser 76 Series - V8 Goodness... - Build coming soon.
8. 1990 Audi 90 manual - The delightfully dignified daily driver
until then:
1. 2001 Merc-Benz A160 (porta-loo on wheels)
2. 2007 Peugeot 307 TDi (more fun than you'd expect)
3. [url=ttp://ftoaustralia.com/v3/viewtopic.php?f=29&t=25373]2009 Mitsubishi Triton Di-D (a monster in its own right)[/url]
4. 1992 Nissan NX Coupe (club car and project car)
5. 1996 Holden SB Barina - "The Nugget"
6. 1996 Jeep XJ Cherokee Sport - The Budget Build
7. 2010 Toyota Landcruiser 76 Series - V8 Goodness... - Build coming soon.
8. 1990 Audi 90 manual - The delightfully dignified daily driver
Astron_Boy wrote:No correction needed Gen Y, you are correct.
Bennoz wrote:My rubbing happens on the inside.
- Vectose
- Forum Moderator
- Posts: 3952
- Joined: Sun Nov 28, 2010 8:45 pm
- Location: Newcastle
Re: Cusco Comp 2 Coilovers
What would the advantage be with getting coilovers with similar spring rates to lowered springs? (Besides the obvious adjustability)
I have RSR Ti2000 springs and I am pretty happy with the ride. Spring rates are 3.3 front and 2.5 rear.
Stock spring rates are 2.6 front and 1.6 rear.
Compared to BC coilovers which are 7 front and 5 rear......
EDIT: And we should probably get a mod to move all this talk.
I have RSR Ti2000 springs and I am pretty happy with the ride. Spring rates are 3.3 front and 2.5 rear.
Stock spring rates are 2.6 front and 1.6 rear.
Compared to BC coilovers which are 7 front and 5 rear......
EDIT: And we should probably get a mod to move all this talk.
Bennoz wrote:A whoooole lot 'o jismTechnikhaus wrote:What is in said Bens big penis by the way?
- fraz91
- Hair-do
- Posts: 881
- Joined: Sun Jan 17, 2010 6:00 pm
- Location: 4wding over you, Sydney
Re: Cusco Comp 2 Coilovers
Haha, yeahVectose wrote:What would the advantage be with getting coilovers with similar spring rates to lowered springs? (Besides the obvious adjustability)
I have RSR Ti2000 springs and I am pretty happy with the ride. Spring rates are 3.3 front and 2.5 rear.
Stock spring rates are 2.6 front and 1.6 rear.
Compared to BC coilovers which aer 7 front and 5 rear......
EDIT: And we should probably get a mod to move all this talk.
With the BC's and other top-brand coilovers, you'll often find they run two coils on each strut. One is the high spring rate designed for handling and holding the height of the vehicle, the other is a much softer "damper spring" that sits between the coil seat and the heavy spring. The idea here is that the damper spring squashes up under the vehicle weight, but takes out a lot of the jarring and discomfort from the heavy springs, while the heavier spring supports the majority of the vehicle weight and gives it the performance you need. I know the HKS FTO has BC coilovers in it, and they don't ride too badly.
edit- Here's some on the ohlins shocks, they're the small blue coil under the yellow one
I'll have an FTO one day... i swear!
until then:
1. 2001 Merc-Benz A160 (porta-loo on wheels)
2. 2007 Peugeot 307 TDi (more fun than you'd expect)
3. [url=ttp://ftoaustralia.com/v3/viewtopic.php?f=29&t=25373]2009 Mitsubishi Triton Di-D (a monster in its own right)[/url]
4. 1992 Nissan NX Coupe (club car and project car)
5. 1996 Holden SB Barina - "The Nugget"
6. 1996 Jeep XJ Cherokee Sport - The Budget Build
7. 2010 Toyota Landcruiser 76 Series - V8 Goodness... - Build coming soon.
8. 1990 Audi 90 manual - The delightfully dignified daily driver
until then:
1. 2001 Merc-Benz A160 (porta-loo on wheels)
2. 2007 Peugeot 307 TDi (more fun than you'd expect)
3. [url=ttp://ftoaustralia.com/v3/viewtopic.php?f=29&t=25373]2009 Mitsubishi Triton Di-D (a monster in its own right)[/url]
4. 1992 Nissan NX Coupe (club car and project car)
5. 1996 Holden SB Barina - "The Nugget"
6. 1996 Jeep XJ Cherokee Sport - The Budget Build
7. 2010 Toyota Landcruiser 76 Series - V8 Goodness... - Build coming soon.
8. 1990 Audi 90 manual - The delightfully dignified daily driver
Astron_Boy wrote:No correction needed Gen Y, you are correct.
Bennoz wrote:My rubbing happens on the inside.